The U.S. aircraft register, updated daily
Accidents · NTSB CEN25LA086 · Final report

American Champion Aircraft 7ECA incident near Longview, Texas, January 16, 2025

On January 16, 2025 at about 11:00 pm local time, a 2005 American Champion Aircraft 7ECA, registered N798L, was substantially damaged in an incident during maneuvering near Longview, Texas (East Texas Rgnl airport). It was an instructional flight under general aviation rules (Part 91). No one was hurt; 2 people were on board or involved. The weather was visual conditions (good weather).

The NTSB's probable cause their words, unchanged

The failure of the lower hinge barrel due to fatigue cracking. Contributing to the failure of the lower hinge barrel was increased stress from end face contact likely associated with worn bushings or displaced needle bearings.

Source: NTSB aviation accident database, copy made November 2, 2026. Docket and reports at the NTSB.

What the record shows

Date
January 16, 2025 · about 11:00 pm local time · cases in 2025
Place
Longview, Texas · East Texas Rgnl · cases near this airport · map
Type
Incident
Injuries
No one was hurt; 2 people were on board or involved.
Weather
visual conditions (good weather)
Aircraft
American Champion Aircraft 7ECA NO SERIES, built 2005 · all 7ECAs on the register
Registration
N798L · registry record · serial 1393-2005
Damage
Substantial damage
Flight
Instructional flight · general aviation rules (Part 91)

The NTSB's narrative final · quoted from the NTSB record

After the uneventful instructional flight landed, the airplane was shut down on the ramp. A second flight instructor and student pilot then completed a preflight inspection before their planned instructional flight. During their preflight inspection, the lower hinge for the rudder was found fractured from the vertical spar tube. Examination of the rudder and the lower hinge attachment hardware revealed the lower hinge barrel fractured from fatigue cracking that initiated along the toe of the weld that joined the hinge barrel and the rudder post. Cracking started on both the outer and inner surfaces of the lower rudder post, propagating into the post cross section, consistent with reverse-bending fatigue. The inner surface cracking initiated from small corrosion pits on the inside surface, and the outer surface fatigue cracking initiated along geometrical features at the weld toe that acted as stress concentration sites. The fatigue cracking propagated from the top down the left and right sides until the final overstress detached a small downward-facing ligament of the post at an unknown time. A black protective coating had been applied to the frame of the rudder post. This layer was consistent with the prescribed black powder coating from manufacture. A successive series of paint layers were present on top of this black coating: white, red, white, and then blue on the exterior. The white layers were likely primer. The blue and white paint layers covered areas of the post where cracks had developed. However, worn surfaces on the hinge knuckles were also covered with blue paint, indicating the rudder post had operated for some time before the paint was applied. The presence of corrosion pitting suggests that the paint and other coatings were either not sufficient to protect the underlying alloy surfaces or were compromised during the rudder’s life. The rudder is expected to accommodate the variable loads that stress the upper and lower hinge knuckle attachments during normal operation. However, the contact that produced wear at the hinge barrels could have contributed to elevated stress at the attachment locations. The vertical stabilizer carries vertical and lateral loads from rudder accelerations and surface pressures through the upper and lower hinges. The weld toes between the hinge barrels and the rudder post would concentrate these variable stresses at this location; additionally, both hinge barrels' lower surfaces were worn, indicating prolonged surface contact with an associated increase in stress. While fatigue cracking had initiated at both the inner and outer surfaces of the rudder post, the extent of crack growth propagating from the exterior surface indicates the primary initiation area was along the toe of the weld. According to the FAA, where the airplane was based is classified as an area of having moderate corrosive exposure for aircraft structures. Based on the available evidence, the lower hinge barrel likely failed due to fatigue cracking at an unknown time. Contributing to the failure of the lower hinge barrel was increased stress from end face contact likely associated with worn bushings or displaced needle bearings. After the incident, the operator and the airframe manufacturer both expanded their inspection requirements for these areas by using magnification glass visual and dye penetrant inspections, which will likely enhance future crack detection by maintenance personnel.

The complete narrative as the NTSB published it. The NTSB's docket holds the report as a PDF and any photographs, statements and other documents from the investigation.

The factual record from the NTSB's investigation tables, in plain English

What happened, in order

  1. Flight control sys malf/fail during maneuvering defining event

The NTSB's findings

Pilot

  • Flight time: 0 hours in all; 0 in this make and model
  • Medical certificate: Unknown
  • Seat: unk
  • Injury: unkn

The aircraft

  • Airframe total time: 8,353.2 hours
  • Last inspection: 100-hour inspection, November 12, 2024; 58.6 hours since
  • Maximum gross weight: 1,750 lb
  • Seats: 2
  • Landing gear: fixed
  • Engine: Lycoming Engines O-235-K2C (piston); 5,958 hours total
  • Operator: Letourneau University

The flight

  • Departed from: 07F Gladewater TX at 10:37 pm
  • Destination: GGG Longview TX
  • Flight plan: none
  • Runway 18/3, 6,110 ft by 150 ft
  • A second pilot was aboard

Weather at the time

  • Light: daylight
  • Wind: from 170° at 11 knots
  • Visibility: 10 statute miles
  • Sky: a few clouds at 3,400 ft
  • Temperature: 55°F (13°C), dew point 46°F (8°C)
  • Altimeter: 29.74 inHg
  • Observation at 4:53 pm from KGGG

Weather report (METAR): KGGG 172253Z 17011KT 10SM FEW034 13/08 A2974 RMK AO2 SLP072 T01280078

Injuries

FatalSeriousMinorNone
Flight crew2

Photographs from the investigation 5 pictures from the NTSB's docket, as the NTSB released them

The NTSB's photographs with the NTSB's captions, at screen size. Open a picture to see it full size or to report one that should not be shown.

Documents from the investigation the NTSB's docket: the evidence folder behind the report

14 documents, released by the NTSB on October 16, 2026. View them here, or download them; the NTSB redacts some personal details before release, and this site shows the NTSB's own titles rather than its file names.

The same docket at the NTSB · documents without a copy here are fetched from the NTSB when you open them.

Other NTSB records under N798L the same tail number, which may have belonged to a different aircraft at the time

2024-04-15CEN24LA171 · accident near Lakeport, TX · substantial damage · no injuries

Connections how this case links to the rest of the register

Aircraft
Place
Record

The whole map of how records connect · these connections as data: /graph/accident/CEN25LA086.json.

The bigger picture in Aviation Analytics: accidents over time since 1982, by model, by phase of flight and conditions, by place and on the map.

Everything on this page comes from the NTSB's public records. The narrative, probable cause and findings are the NTSB's own words; the coded tables behind the report are written out in plain English, with pilots' ages, home towns and medical details left out. The documents and photographs are the NTSB's docket, shown as the NTSB released them. This site's own text does not name anyone involved, its policy at this time. A preliminary report can change; the final report usually follows one to two years later, and the page is refreshed when it does.