2022-02-03: Turbine Engine Accessory Drive

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by: a. Removing airworthiness directive 2013-26-01, Amendment 39-17710 (78 FR 79295, December 30, 2013); and b. Adding the following new airworthiness directive: 2022-02-03 CFM International, S.A.: Amendment 39-21900; Docket No. FAA-2021-0259; Project Identifier AD-2020-01128-E. (a) Effective Date This airworthiness directive (AD) is effective March 22, 2022. (b) Affected ADs This AD replaces AD 2013-26-01, Amendment 39-17710 (78 FR 79295, December 30, 2013). (c) Applicability This AD applies to CFM International, S.A. CFM56-3 and CFM56-7B model turbofan engines equipped with an accessory gearbox (AGB) assembly with the following part numbers (P/Ns): (1) For CFM56-3, CFM56-3B, and CFM56-3C model turbofan engines, AGB P/N: 335- 300-103-0, 335-300-105-0, 335-300-106-0, 335-300-107-0, 335-300-108-0, 335-300-109-0, or 335-300-110-0, installed. (2) For CFM56-7B20, CFM56-7B20/2, CFM56-7B20/3, CFM56-7B22, CFM56-7B22/2, CFM56-7B22/3, CFM56-7B22/3B1, CFM56-7B22/B1, CFM56-7B24, CFM56-7B24/2, CFM56-7B24/3, CFM56-7B24/3B1, CFM56-7B24/B1, CFM56-7B26, CFM56-7B26/2, CFM56-7B26/3, CFM56-7B26/3B1, CFM56-7B26/3B2, CFM56-7B26/3B2F, CFM56-7B26/3F, CFM56-7B26/B1, CFM56-7B26/B2, CFM56-7B27, CFM56-7B27/2, CFM56-7B27/3, CFM56-7B27/3B1, CFM56-7B27/3B1F, CFM56-7B27/3B3, CFM56-7B27/3F, CFM56-7B27/B1, and CFM56-7B27/B3 model turbofan engines, AGB P/N: 340-046-503-0, 340-046-504-0, or 340-046-505-0, installed. (3) For CFM56-7B27A, CFM56-7B27A/3, or CFM56-7B27AE model turbofan engines, AGB P/N: 340-188-601-0, 340-188-603-0, or 340-188-605-0, installed. (d) Subject Joint Aircraft System Component (JASC) Code 7260, Turbine Engine Accessory Drive. (e) Unsafe Condition This AD was prompted by a dual engine loss of oil event and 42 prior events of total loss of engine oil during flight. The FAA is issuing this AD to prevent loss of engine oil while in flight. The unsafe condition, if not addressed, could result in engine failure, loss of thrust control, reduced control of the aircraft, and damage to the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Required Actions (1) After the effective date of this AD, after any maintenance that involves removal and re-installation of the AGB handcranking pad cover, perform an independent inspection to verify re-installation of the AGB handcranking pad cover; or (2) Prior to the next removal of the AGB handcranking pad cover from the engine, insert the independent inspection required by paragraph (g)(1) of this AD as a required inspection item in the existing approved continuous airworthiness maintenance program for the aircraft. (h) Mandatory Terminating Action As a mandatory terminating action to the requirements of paragraph (g) of this AD: (1) For affected CFM56-3, CFM56-3B, and CFM56-3C model turbofan engines, at the next engine shop visit, or before December 31, 2026, whichever occurs first after the effective date of this AD, replace the affected AGB with a part eligible for installation. (2) For affected CFM56-7B model turbofan engines, except for CFM56-7B27A, CFM56-7B27A/3, and CFM56-7B27AE model turbofan engines, at the next engine shop visit, or before December 31, 2024, whichever occurs first after the effective date of this AD, replace the affected AGB with a part eligible for installation. (i) Definition (1) For the purpose of this AD, an "engine shop visit" is the induction of an engine into the shop for maintenance involving the separation of pairs of major mating engine case flanges, except for the following situations, which do not constitute an engine shop visit: (i) Separation of engine flanges solely for the purposes of transportation of the engine without subsequent maintenance; or (ii) Separation of engine flanges solely for the purpose of replacing the fan or propulsor without subsequent maintenance. (2) For the purpose of this AD, for affected CFM56-3, CFM56-3B, and CFM56-3C model turbofan engines, a part eligible for installation is: (i) An AGB with a P/N other than 335-300-103-0, 335-300-105-0, 335-300-106-0, 335-300-107-0, 335-300-108-0, 335-300-109-0, 335-300-110-0; or (ii) An AGB that, using an FAA-approved procedure, has been re-worked with a dynamic oil seal in the handcranking pad cover assembly and re-identified with a new P/N not listed in paragraph (i)(2)(i) of this AD. Note 1 to paragraph (i)(2)(ii): Procedures to install a dynamic oil seal in the handcranking pad cover assembly can be found in CFM International SB CFM56-3S/B 72-1129, Revision 7, dated May 6, 2020. (3) For the purpose of this AD, for affected CFM56-7B model turbofan engines, except for CFM56-7B27A, CFM56-7B27A/3, and CFM56-7B27AE model turbofan engines, a part eligible for installation is: (i) An AGB with a P/N other than 340-046-503-0, 340-046-504-0, or 340-046-505-0; or (ii) An affected AGB that, using an FAA-approved procedure, has been re-worked with a dynamic oil seal in the handcranking pad cover assembly and re-identified with a new P/N not listed in paragraph (i)(3)(i) of this AD. Note 2 to paragraph (i)(3)(ii): Procedures to install a dynamic oil seal in the handcranking pad cover assembly can be found in CFM International SB CFM56-7BS/B 72-0879, Revision 7, dated February 10, 2021, CFM56-7B S/B 72-0564, Revision 9, dated December 3, 2021, or CFM56-7B S/B 72-1071, initial issue, dated December 3, 2021. (j) Alternative Methods of Compliance (AMOCs) (1) The Manager, ECO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the certification office, send it to the attention of the person identified in paragraph (k) of this AD. You may email your request to: ANE-AD-AMOC@faa.gov. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (k) Related Information For more information about this AD, contact Kevin Clark, Aviation Safety Engineer, ECO Branch, FAA, 1200 District Avenue, Burlington, MA 01803; phone: (781) 238-7088; fax: (781) 238-7199; email: kevin.m.clark@faa.gov. (l) Material Incorporated by Reference None. Issued on February 23, 2022. Derek Morgan, Acting Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2022-04149 Filed 2-28-22; 8:45 am]BILLING CODE 4910-13-P