2024-10-12: Fuel system wiring

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2024-10-12 Bell Helicopter Textron Canada Limited: Amendment 39-22758; Docket No. FAA-2024-0232; Project Identifier MCAI-2023-00353-R. (a) Effective Date This airworthiness directive (AD) is effective August 22, 2024. (b) Affected ADs None. (c) Applicability This AD applies to Bell Textron Canada Limited Model 407 helicopters, serial numbers 54832 through 54931 inclusive, 54933 through 54939 inclusive, and 54942 through 54954 inclusive, certificated in any category, with a fuel system standpipe assembly (standpipe) part number 407-062-032-103 installed. (d) Subject Joint Aircraft System Component (JASC) Code: 2897, Fuel system wiring. (e) Unsafe Condition This AD was prompted by a report that certain standpipes may have sharp edges at the interval weld joints due to a quality escape during the manufacturing process. The FAA is issuing this AD to detect sharp edges in the standpipe. The unsafe condition, if not addressed, could result in fuel quantity system wiring damage, loss of or erratic fuel quantity indication. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements (1) Within 300 hours time-in-service (TIS) or 6 months after the effective date of this AD, whichever occurs first, accomplish the actions required by paragraphs (g)(1)(i) and (ii) of this AD. (i) With the standpipe removed from the aft fuel cell, inspect the interior of the standpipe for any sharp edges on each internal weld joint, as shown in Figure 1 of Bell Alert Service Bulletin 407-21-124, dated February 1, 2022. If there is a sharp edge on any internal weld joint, before further flight, deburr the edges of each affected weld joint using an aluminum oxide abrasive cloth or paper, or equivalent, ensuring not to exceed 0.015 in (0.38 mm) depth into the tube material at a 45-degree angle to the weld joint. Then, using a clean cloth dampened with isopropyl alcohol or equivalent, remove all sanding residue from the weld joint and apply a chemical film material to any bare metal surfaces. (ii) With the fuel quantity harness assembly (harness assembly) removed, inspect the harness assembly connectors for any mechanical damage and corrosion to the electrical pins and inspect the insulation tubing and wires for any cracks and chafing. For the purposes of this AD, mechanical damage is indicated by deterioration of the connections or pins. (A) If there is any corrosion or mechanical damage, before further flight, remove the harness assembly from service and replace it with an airworthy harness assembly. (B) If there is a crack or any chafing, before further flight, remove the harness assembly from service and replace it with an airworthy harness assembly. (2) If the harness assembly was required to be replaced as a result of the inspection required by paragraph (g)(1)(ii) of this AD or by this paragraph, before further flight, with the standpipe and harness assembly installed, perform a fuel quantity gauging system calibration in accordance with paragraphs 4 through 18 of Fuel Quantity Gauging System, DMC-407-A-95-65-10-01A-273A-A, dated June 2, 2022, of Chapter 95-Instruments, of Bell Model 407 Maintenance Manual, BHT-407-MM, Issue No. 014, dated December 12, 2023. As a result of the fuel quantity gauging system calibration, if a fuel level does not indicate the correct reading or displays no reading, before further flight, remove the harness assembly from service and replace it with an airworthy harness assembly; and repeat the actions required by this paragraph for the newly installed harness assembly. (h) Alternative Methods of Compliance (AMOCs) (1) The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the International Validation Branch, send it to the attention of the person identified in paragraph (i) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. The following provisions also apply to this AD. (i) Related Information For more information about this AD, contact Michael Hughlett, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: (817) 222-5889; email: michael.Hughlett@faa.gov. (j) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) Bell Alert Service Bulletin 407-21-124, dated February 1, 2022. (ii) Fuel Quantity Gauging System, DMC-407-A-95-65-10-01A-273A-A, dated June 2, 2022, of Chapter 95-Instruments, of Bell Model 407 Maintenance Manual, BHT-407-MM, Issue No. 014, dated December 12, 2023. (3) For Bell Helicopter Textron Canada Limited material, contact Grant Walker, 330 Sparks St., Ottawa, K1A 0N5, Canada; phone: (888) 663-3639; email: grant.walker@tc.gc.ca. (4) You may view this material at the FAA, Office of the Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 6N-321, Fort Worth, TX 76177. For information on the availability of this material at the FAA, call (817) 222-5110. (5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email fr.inspection@nara.gov. Issued on July 10, 2024. James D. Foltz, Deputy Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2024-15808 Filed 7-17-24; 8:45 am]BILLING CODE 4910-13-P