97-19-06: Blade Trailing Edge Pocket Assemblies

97-19-06 SIKORSKY AIRCRAFT CORPORATION: Amendment 39-10126. Docket No. 97-SW-18-AD. Supersedes priority letter AD 97-10-04, issued April 30, 1997. Applicability: Model S-61A, D, E, L, N, NM, R, and V helicopters, certificated in any category, with a main rotor blade assembly (blade), part number (P/N) S6115-20501 or P/N 61170-20201, installed, having one of the following four-digit or eight-digit serial numbers: 1282-1554 2721 3016-2850 3305-3106 3517-3311 4787-4793 2183 2751 3019 3317-3115 3525-3310 4800-4794 2380-2498 2781-2644 3138 3343-3147 3637-3459 4835-4790 2495 2800-2671 3168-3585 3343-3648 3694-3481 5484-5363 2500 2817 3192-2999 3364-3180 3748-3543 5974-5816 2520 2819 3215-3012 3451-3239 3752-3527 5981-5813 2521 2839 3216-3023 3491-3278 3753-3528 7069-6583 2644 2883 3242-3044 3499-3936 3840-3620 7779-7033 2673 2919-2771 3249-3052 3511-3293 3966-3737 8099-8054 2716-2683 3008 3250-3043 3512-3292 4216-4392 NOTE 1: This AD applies to each helicopter identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For helicopters that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must use the authority provided in paragraph (b) to request approval from the FAA. This approval may address either no action, if the current configuration eliminates the unsafe condition, or different actions necessary to address the unsafe condition described in this AD. Such a request should include an assessment of the effect of the changed configuration on the unsafe condition addressed by this AD. In no case does the presence of any modification, alteration, or repair remove any helicopter from the applicability of this AD. Compliance: Required before further flight, unless accomplished previously.To prevent disbonding and separation of portions of the blade, subsequent excessive vibrations, and loss of control of the helicopter, accomplish the following: (a) Inspect each blade having one of the affected serial numbers in accordance with Section 2A of the Accomplishment Instructions of Sikorsky Alert Service Bulletin (ASB) No. 61B15-29A, Revision A, dated May 9, 1997, to determine the anodizing date for all blade trailing edge pocket assemblies (pocket assemblies) installed on the blade in locations as specified in the Planning Information Section, paragraph 1D(3) of the ASB, that were anodized by Poly-Metal Company. Remove any blade having a pocket assembly anodized by Poly-Metal Company during the period from October 1, 1996 through December 31, 1996, and replace the blade with an airworthy blade. (b) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, BostonAircraft Certification Office, FAA. Operators shall submit their requests through an FAA Principal Maintenance Inspector, who may concur or comment and then send it to the Manager, Boston Aircraft Certification Office. NOTE 2: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the Boston Aircraft Certification Office. (c) A one-time only special flight permit may be issued to operate the helicopter to a location where the requirements of this AD can be accomplished, after inspecting all pocket assemblies for disbonding. (d) The inspection shall be done in accordance with Sikorsky ASB No. 61B15-29A, Revision A, dated May 9, 1997. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from Sikorsky Aircraft Corporation, Attn: Mr. Paul Dionne, CAR Office, 6900 Main Street, P.O. Box 9729, Stratford, Connecticut 06497-9129, telephone (203) 386-7860, fax (203) 386-4703. Copies may be inspected at the FAA, Office of the Assistant Chief Counsel, 2601 Meacham Blvd., Room 663, Fort Worth, Texas; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC. (e) This amendment becomes effective on October 6, 1997.