The U.S. aircraft register, updated daily
FAA orders · airworthiness directive · current

61-22-01: Pitch Link Rod End Bearing

FAA order 61-22-01 is an airworthiness directive in force since November 7, 1961. The FAA's subject line: Pitch Link Rod End Bearing. It names Bell-Carson 47, Bell 47: about 483 aircraft on the U.S. register today across them, though an order usually covers particular versions or serial numbers rather than every one. System: other and general.

What it applies to as the FAA lists it

Kind of product
Aircraft
Makes
Scotts-Bell 47 Inc
Models
47, 47B, 47B3, 47D, 47D1, 47E, 47G, 47G-2, 47G-2A, 47G-2A-1, 47G-3, 47G-3B, 47G-3B-1, 47G-3B-2, 47G-3B-2A, 47G-4, 47G-4A, 47G-5, 47G-5A, 47H-1, 47J, 47J-2, 47J-2A, 47K
On this site
Bell-Carson 47 5 registered
Bell 47 478 registered

Dates and paperwork

In force since
November 7, 1961
Published
November 7, 1961
Docket
Unknown
Status
Current
The FAA's document
Read the order on the FAA's site

The order itself the regulatory text, as published

Show the full text (2,115 characters)
61-22-01 BELL: Amdt. 361 Part 507 Federal Register November 7, 1961. Applies to All Model 47 Series Helicopters. Compliance required as indicated. To preclude failure of the main rotor pitch link rod end bearing P/N RE4F7 which causes loss of main rotor control, the following one-time only inspection is required to determine that the bearing is correctly installed. (a) Within the next 10 hours' time in service after the effective date of this AD, on all Model 47 Series helicopters, inspect the main rotor control pitch link located between the stabilizer bar mixing lever and the main rotor blade control horn to see that the rod end bearing sides are parallel to the clevis slot. These surfaces must be adjusted parallel to prevent binding of the rod end bearing at extreme ends of travel, as specified in all applicable model maintenance manuals. (b) Within the next 10 hours' time in service after the effective date of this AD, inspect all Models 47D, 47D-1, 47H-1, 47G, 47G-2, and 47J helicopters equipped with Fafnir P/N RE4F7 rod end bearing as follows: (1) Remove the RE4F7 rod end bearing in accordance with the applicable maintenance manual and visually inspect for obvious damage or defect of the outer race such as nicks and gouges adjacent to the shield, looseness, roughness, distortion or kinks in bearing shields. (2) If any damage or defect is found, replace the bearing prior to further flight. (3) If no damage or defect is found, the bearing may be reinstalled. (4) The installation of the bearings under subparagraphs (2) or (3) shall be made in accordance with the applicable maintenance manual making positive that requirements of paragraph (a) are followed. (c) Helicopters listed in paragraph (b) that are not equipped with the Fafnir P/N RE4F7 bearings are equipped with Bell P/N 47-140-241-3 rod end bearings. These bearings are of a different make and only require the inspection called for in paragraph (a).(Bell Service Instruction 345 SI covers this same subject for the models listed under (b)). This directive effective November 7, 1961.

Related safety bulletins advice on the same designs, not orders

2001-02-09SW-01-13 ·

Source: FAA Dynamic Regulatory System, airworthiness directives. The FAA's document is the authority; the register counts are this site's, from the FAA register of October 23, 2026. Connections as data: /graph/directive/61-22-01.json · aircraft systems.