The U.S. aircraft register, updated daily
FAA orders · airworthiness directive · current

2026-22-10: Tail rotor blades

FAA order 2026-22-10 is an airworthiness directive in force since December 14, 2026. The FAA's subject line: Tail rotor blades. It names Airbus Helicopters EC-135 now H135: about 397 aircraft on the U.S. register today, though an order usually covers particular versions or serial numbers rather than every one. System: rotorcraft systems.

What it applies to as the FAA lists it

Kind of product
Aircraft
Makes
Airbus Helicopters Deutschland GmbH (AHD)
Models
EC135P1, EC135P2, EC135P2+, EC135P3, EC135T1, EC135T2, EC135T2+, EC135T3, EC635T2+
On this site
Airbus Helicopters EC-135 now H135 397 registered

Dates and paperwork

In force since
December 14, 2026
Published
November 9, 2026 (signed October 30, 2026)
Docket
FAA-2026-7230
Replaces
2024-04-10
Status
Current
The FAA's document
Read the order on the FAA's site

The FAA's summary their words, unchanged

The FAA is superseding Airworthiness Directive (AD) 2024-04-10 which applied to all Airbus Helicopters Deutschland GmbH (AHD) Model EC135P1, EC135P2, EC135P2+, EC135P3, EC135T1, EC135T2, EC135T2+, EC135T3, and EC635T2+ helicopters. AD 2024-04-10 required repetitively inspecting certain part-numbered tail rotor (T/R) blades for a crack and, depending on the results, removing any cracked T/R blade from service. AD 2024-04-10 also prohibits installing certain T/R blades on any helicopter unless certain requirements are met. Since AD 2024-04-10 was issued, it was determined that inspection Method A should be discontinued and that additional limitations shall be provided. This AD retains the actions of AD 2024-04-10 and requires repetitively inspecting a certain tail rotor blade (TRB) assembly for cracks and, depending on the results, removing any cracked TRB assembly from service and replacing an affected part as terminating action for the repetitive inspections. This AD also prohibits installing an affected TRB assembly on any helicopter unless certain requirements are met. The FAA is issuing this AD to address the unsafe condition on these products.

The order itself the regulatory text, as published

Show the full text (7,440 characters)
1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by: a. Removing Airworthiness Directive 2024-04-10, Amendment 39-22689 (89 FR 15431, March 4, 2024); and b. Adding the following new airworthiness directive: 2026-22-10 Airbus Helicopters Deutschland GmbH (AHD): Amendment 39-23512; Docket No. FAA-2026-7230; Project Identifier MCAI-2026-00185-R. (a) Effective Date This airworthiness directive (AD) is effective December 14, 2026. (b) Affected ADs This AD replaces AD 2024-04-10, Amendment 39-22689 (89 FR 15431, March 4, 2024) (AD 2024-04-10). (c) Applicability This AD applies to all Airbus Helicopters Deutschland GmbH (AHD) Model EC135P1, EC135P2, EC135P2+, EC135P3, EC135T1, EC135T2, EC135T2+, EC135T3, and EC635T2+ helicopters, certificated in any category. (d) Subject Joint Aircraft System Component (JASC) Code 6410, Tail rotor blades. (e) Unsafe Condition This AD was prompted by a report of a separated tail rotor blade (TRB) assembly due to a crack in the TRB assembly caused by intergranular corrosion. The FAA is issuing this AD to detect and address cracks in the TRB assembly. The unsafe condition, if not addressed, could result in separation of a TRB assembly and reduced control of the helicopter. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraphs (h) and (i) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency AD 2026-0032, dated February 19, 2026 (EASA AD 2026-0032). (h) Exceptions to EASA AD 2026-0032 (1) Where EASA AD 2026-0032 refers to its effective date, this AD requires using the effective date of this AD. (2) Where EASA AD 2026-0032 refers to January 29, 2024 (the effective date of EASA Emergency AD 2024-0028-E), this AD requires using March 19, 2024 (the effective date of AD 2024-04-10). (3) Where EASA AD 2026-0032 refers to flight hours, this AD requires using hours time-in-service (TIS). (4) Where paragraph (1) of EASA AD 2026-0032 specifies "Before an affected part exceeds 685 FH [flight hours] since first installation on a helicopter", this AD requires replacing that text with "Before an affected part accumulates 685 hours TIS since first installation on a helicopter, or within 10 hours TIS after March 19, 2024 (the effective date of AD 2024-04-10), whichever occurs later". (5) Where paragraph 4.3 of the material referenced in EASA AD 2026-0032 recommends type II visible dye inspections, this AD requires the inspection methods in paragraphs (h)(5)(i), (ii), or (iii) of this AD, as applicable: (i) If the affected part has previously been inspected using a type II visible dye method, perform type II visible dye (Method B of the material referenced in EASA AD 2026-0032) or eddy current inspections, instead of fluorescent penetrant inspections. (ii) If the affected part has not previously been inspected using a type II visible dye inspection, perform eddy current or fluorescent penetrant inspections, instead of type II visible dye inspections. (iii) If you cannot determine whether the affected part has previously been inspected by a type II visible dye method, clean all surfaces to be inspected and perform an eddy current or a fluorescent penetrant inspection, instead of a type II visible dye inspection. Note 1 to paragraph (h)(5): The FAA reminds operators of the airworthiness concern regarding type II visible dye inspections of critical parts discussed in FAA Special Airworthiness Information Bulletin (SAIB) CE-18-26R1, dated October 30, 2018 (SAIB CE-18-26R1). SAIB CE-18-26R1 explains the risks associated with using type II visible dye inspection methods, including the prohibition in ASTM E1417 on the use of type II visible dye penetrant prior to the use of type I fluorescent penetrant on the same surface. SAIB CE-18-26R1 also advises of the importance of pre- and post-inspection cleaning to ensure proper detection of cracks. You can find SAIB CE-18-26R1 at drs.faa.gov. Note 2 to paragraph (h)(5): The material referenced in EASA AD 2026-0032 identifies a type II visible dye inspection as Method A (not allowed) or Method B; eddy current inspection as Method C; fluorescent penetrant inspection as Method D; and visual inspection as Method E. Note 3 to paragraph (h)(5): When entering compliance with the applicable paragraph of the AD into the helicopter maintenance records, documenting that a type II visible dye inspection was performed improves the accuracy of maintenance records. (6) This AD does not adopt paragraph (3) of EASA AD 2026-0032. (7) This AD does not adopt the "Remarks" section of EASA AD 2026-0032. (i) No Reporting or Returning of Parts Where the material referenced in EASA AD 2026-0032 specifies to submit certain information and to send removed parts to the manufacturer, this AD does not include those actions. (j) Special Flight Permits Special flight permits, as described in 14 CFR 21.197 and 21.199, are not allowed. (k) Alternative Methods of Compliance (AMOCs) (1) The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards District Office, as appropriate. If sending information directly to the manager of the International Validation Branch, send it to the attention of the person identified in paragraph (l) of this AD and email to [email protected]. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (l) Additional Information For more information about this AD, contact Soban Saeed, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: (316) 946-4123; email: [email protected]. (m) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this material as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2026-0032, dated February 19, 2026. (ii) [Reserved] (3) For EASA material identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; phone: +49 221 8999 000; email: [email protected]; website: easa.europa.eu. You may find the EASA material on the EASA website at ad.easa.europa.eu. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 10101 Hillwood Parkway, Fort Worth, TX 76177. For information on the availability of this material at the FAA, call (817) 222-5110. (5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email [email protected]. Issued on October 30, 2026. Steven W. Thompson, Acting Deputy Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2026-22776 Filed 11-6-26; 8:45 am]BILLING CODE 4910-13-P

Related safety bulletins advice on the same designs, not orders

2012-10-03SW-12-45 · Garmin Model 400W/500W Series GPS-WAAS Navigation System
2009-05-07SW-09-26 · Operation with Emergency Flotation System ARMED
2008-08-27SW-08-42 · Emergency Float with Liferaft Kits (kits)

Source: FAA Dynamic Regulatory System, airworthiness directives. The FAA's document is the authority; the register counts are this site's, from the FAA register of November 16, 2026. Connections as data: /graph/directive/2026-22-10.json · aircraft systems.