2025-19-09: Time Limits/Maintenance Checks

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by: a. Removing Airworthiness Directive (AD) 2023-05-13, Amendment 39-22382 (88 FR 20749, April 7, 2023); and b. Adding the following new AD: 2025-19-09 Airbus SAS: Amendment 39-23149; Docket No. FAA-2025-0351; Project Identifier MCAI-2024-00480-T. (a) Effective Date This airworthiness directive (AD) is effective December 22, 2025. (b) Affected ADs (1) This AD replaces AD 2023-05-13, Amendment 39-22382 (88 FR 20749, April 7, 2023) (AD 2023-05-13). (2) This AD affects AD 2018-18-19, Amendment 39-19398 (83 FR 47056, September 18, 2018) (AD 2018-18-19). (c) Applicability This AD applies to all Airbus SAS airplanes, certificated in any category, identified in paragraphs (c)(1) through (4) of this AD. (1) Model A300 B4-601, B4-603, B4-620, and B4-622 airplanes. (2) Model A300 B4-605R and B4-622R airplanes. (3) Model A300 C4-605R Variant F airplanes. (4) Model A300 F4-605R and F4-622R airplanes. (d) Subject Air Transport Association (ATA) of America Code 05, Time Limits/Maintenance Checks. (e) Unsafe Condition This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. The FAA is issuing this AD to address fatigue damage in principal structural elements. The unsafe condition, if not addressed, could result in reduced structural integrity of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Retained Revision of the Existing Maintenance or Inspection Program, With a New Terminating Action This paragraph restates the requirements of paragraph (g) of AD 2023-05-13, with a new terminating action. Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2022-0173, dated August 24, 2022 (EASA AD 2022-0173). Accomplishing the revision of the existing maintenance or inspection program required by paragraph (k) of this AD terminates the requirements of this paragraph. (h) Retained Exceptions to EASA AD 2022-0173, With No Change This paragraph restates the exceptions specified in paragraph (h) of AD 2023-05-13, with no change. (1) This AD does not adopt the requirements specified in paragraph (1) of EASA AD 2022-0173. (2) Paragraph (2) of EASA AD 2022-0173 specifies revising "the approved AMP" within 12 months after its effective date, but this AD requires revising the existing maintenance or inspection program, as applicable, within 90 days after May 12, 2023 (the effective date of AD 2023-05-13). (3) The initial compliance time for doing the tasks specified in paragraph (2) of EASA AD 2022-0173 is at the applicable "limitations" as incorporated by the requirements of paragraph (2) of EASA AD 2022-0173, or within 90 days after May 12, 2023 (the effective date of AD 2023-05-13), whichever occurs later. (4) This AD does not adopt the provisions specified in paragraph (3) of EASA AD 2022-0173. (5) This AD does not adopt the "Remarks" section of EASA AD 2022-0173. (i) Retained Provisions for Alternative Actions and Intervals, With a New Exception This paragraph restates the requirements of paragraph (i) of AD 2023-05-13, with a new exception. Except as required by paragraph (k) of this AD: After the existing maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions ( e.g., inspections) and intervals are allowed unless they are approved as specified in the provisions of the "Ref. Publications" section of EASA AD 2022-0173. (j) Retained Terminating Action for Certain Tasks Required by AD 2018-18-19, With No Changes This paragraph restates the terminating action of paragraph (j) of AD 2023-05-13, with no changes. For Model A300 B4-601, B4-603, B4-620, B4-622, B4-605R, B4-622R, C4-605R Variant F, F4-605R, and F4-622R airplanes only: Accomplishing the actions required by paragraph (g) of this AD terminates the corresponding requirements of AD 2018-18-19 for the tasks identified in the material referenced in EASA AD 2022-0173 only. (k) New Revision of the Existing Maintenance or Inspection Program Except as specified in paragraph (l) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2024-0164, dated August 21, 2024 (EASA AD 2024-0164). Accomplishing the revision of the existing maintenance or inspection program required by this paragraph terminates the requirements of paragraph (g) of this AD. (l) Exceptions to EASA AD 2024-0164 (1) This AD does not adopt the requirements specified in paragraph (1) of EASA AD 2024-0164. (2) Paragraph (2) of EASA AD 2024-0164 specifies revising "the approved AMP," within 12 months after its effective date, but this AD requires revising the existing maintenance or inspection program, as applicable, within 90 days after the effective date of this AD. (3) The initial compliance time for doing the tasks specified in paragraph (2) of EASA AD 2024-0164 is at the applicable "limitations" as incorporated by the requirements of paragraph (2) of EASA AD 2024-0164, or within 90 days after the effective date of this AD, whichever occurs later. (4) This AD does not adopt the provisions specified in paragraphs (3) and (4) of EASA AD 2024-0164. (5) This AD does not adopt the "Remarks" section of EASA AD 2024-0164. (m) New Provisions for Alternative Actions and Intervals After the existing maintenance or inspection program has been revised as required by paragraph (k) of this AD, no alternative actions ( e.g., inspections) and intervals are allowed unless they are approved as specified in the provisions of the "Ref. Publications" section of EASA AD 2024-0164. (n) New Terminating Action for AD 2018-18-19 For Model A300 B4-601, B4-603, B4-620, B4-622, B4-605R, B4-622R, C4-605R Variant F, F4-605R, and F4-622R airplanes only: Accomplishing the actions required by paragraph (k) of this AD terminates the corresponding requirements of AD 2018-18-19. (o) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, AIR-520, Continued Operational Safety Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of Continued Operational Safety Branch, send it to the attention of the person identified in paragraph (p) of this AD and email to: AMOC@faa.gov . Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, AIR-520, Continued Operational Safety Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (p) Additional Information For more information about this AD, contact Frank Carreras, Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; phone: 206-231-3539; email: Frank.Carreras@faa.gov. (q) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this material as applicable to do the actions required by this AD, unless this AD specifies otherwise. (3) The following material was approved for IBR on December 22, 2025. (i) European Union Aviation Safety Agency (EASA) AD 2024-0164, dated August 21, 2024. (ii) [Reserved] (4) The following material was approved for IBR on May 12, 2023 (88 FR 20749, April 7, 2023). (i) EASA AD 2022-0173, dated August 24, 2022. (ii) [Reserved] (5) For EASA material identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu. You may find this material on the EASA website at ad.easa.europa.eu. (6) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (7) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email fr.inspection@nara.gov. Issued on October 2, 2025. Peter A. White, Deputy Director, Integrated Certificate Management Division, Aircraft Certification Service. Issued on October 2, 2025. Peter A. White, Deputy Director, Integrated Certificate Management Division, Aircraft Certification Service. [FR Doc. 2025-20015 Filed 11-14-25; 8:45 am]BILLING CODE 4910-13-P