2025-13-12: Flight Controls

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2025-13-12 Airbus SAS: Amendment 39-23078; Docket No. FAA-2025-1352; Project Identifier MCAI-2025-00812-T. (a) Effective Date This airworthiness directive (AD) is effective July 25, 2025. (b) Affected ADs None. (c) Applicability This AD applies to all Airbus SAS Model A350-941 and -1041 airplanes, certificated in any category. (d) Subject Air Transport Association (ATA) of America Code 27, Flight Controls. (e) Unsafe Condition This AD was prompted by a report of loss of control of an outboard aileron surface due to hydraulic fluid contaminating an electronic card of the flight control remote module (FCRM). The FAA is issuing this AD to address FCRM electronic cards exposed to hydraulic fluid contamination. This condition, if not detected and corrected, could lead to runaway of rudder or elevator surface, resulting in loss of control of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraphs (h) and (i) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2025-0129, dated June 5, 2025 (EASA AD 2025-0129). (h) Exceptions to EASA AD 2025-0129 (1) Where EASA AD 2025-0129 refers to "07 May 2025 [the effective date of EASA AD 2025-0099]", this AD requires using the effective date of this AD. (2) Where EASA AD 2025-0129 refers to its effective date, this AD requires using the effective date of this AD. (3) Where paragraph (1) of EASA AD 2025-0129 states "do not swap", for this AD replace that text with "do not replace". (4) Where paragraph (2) of EASA AD 2025-0129 states "is reported on an aeroplane", for this AD replace that text with "is documented in the aircraft maintenance records or has been reported to Airbus". (5) Where Table 1 of EASA AD 2025-0129 states "close to", for this AD replace that text with "adjacent to". (6) This AD does not adopt the "Remarks" section of EASA AD 2025-0129. (i) No Reporting Requirement Although the material referenced in EASA AD 2025-0129 specifies to submit certain information to the manufacturer, this AD does not include that requirement. (j) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, AIR-520, Continued Operational Safety Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the Continued Operational Safety Branch, send it to the attention of the person identified in paragraph (k)(1) of this AD and email to: [email protected] . Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, AIR-520, Continued Operational Safety Branch, FAA.; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (3) Required for Compliance (RC): Except as required by paragraph (j)(2) of this AD, if any material referenced in EASA AD 2025-0129 that contains paragraphs that are labeled as RC, the instructions in RC paragraphs, including subparagraphs under an RC paragraph, must be done to comply with this AD; any paragraphs, including subparagraphs under those paragraphs, that are not identified as RC are recommended. The instructions in paragraphs, including subparagraphs under those paragraphs, not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the instructions identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to instructions identified as RC require approval of an AMOC. (k) Additional Information (1) For more information about this AD, contact Udara Dharmasena, Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; phone: 562-627-5295; email: [email protected]. (2) For Airbus material identified in this AD that is not incorporated by reference, contact Airbus SAS, Airworthiness Office-EAL, Rond-Point Emile Dewoitine No: 2, 31700 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 45 80; email [email protected]; website airbus.com. (l) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this material as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2025-0129, dated June 5, 2025. (ii) [Reserved] (3) For EASA material identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email [email protected]. You may find this material on the EASA website at ad.easa.europa.eu. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email [email protected]. Issued on June 30, 2025. Peter A. White, Deputy Director, Integrated Certificate Management Division, Aircraft Certification Service. [FR Doc. 2025-12858 Filed 7-8-25; 4:15 pm]BILLING CODE 4910-13-P