2024-19-04: Nacelles/pylons

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2024-19-04 Airbus SAS Airplanes: Amendment 39-22846; Docket No. FAA-2024-1881; Project Identifier MCAI-2024-00160-T. (a) Effective Date This airworthiness directive (AD) is effective November 29, 2024. (b) Affected ADs None. (c) Applicability This AD applies to all Airbus SAS Model A350-941 and -1041 airplanes, certificated in any category. (d) Subject Air Transport Association (ATA) of America Code 54, Nacelles/pylons. (e) Unsafe Condition This AD was prompted by reports that engine nacelle anti-icing (NAI) forward bulkheads may have elongated locating holes. The FAA is issuing this AD to address elongated locating holes. The unsafe condition, if not addressed, could result in the fasteners, if loose, to vibrate and cause further elongation of the locating holes, which, eventually, can reduce the NAI performance. This condition, if not detected and corrected, could lead to the undetected loss of NAI protection on both engines, possibly resulting in loss of control of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraphs (h) and (i) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2024-0060R1, dated April 16, 2024 (EASA AD 2024-0060R1). (h) Exceptions to EASA AD 2024-0060R1 (1) Where EASA AD 2024-0060R1 refers to its effective date, this AD requires using the effective date of this AD. (2) Where paragraph (2) of EASA AD 2024-0060R1 specifies if "any discrepancy is detected, before next flight, contact Collins Aerospace for approved corrective action instructions and, within the compliance time specified therein accomplish those instructions accordingly," this AD requires replacing that text with if "any discrepancy is detected, the discrepancy must be repaired before further flight using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature." (3) This AD does not adopt the "Remarks" section of EASA AD 2024-0060R1. (i) No Reporting Required Although EASA AD 2024-0060R1 specifies to submit certain information to the manufacturer, this AD does not include that requirement. (j) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the International Validation Branch, mail it to the address identified in paragraph (k) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature. (3) Required for Compliance (RC): Except as required by paragraph (h)(2) of this AD, if any material contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (k) Additional Information For more information about this AD, contact Dat Le, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7317; email [email protected]. (l) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this material as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2024-0060R1, dated April 16, 2024. (ii) [Reserved] (3) For EASA material identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email [email protected]; website easa.europa.eu. You may find this EASA AD on the EASA website ad.easa.europa.eu. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th Street, Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations, or email [email protected]. Issued on September 13, 2024. Peter A. White, Deputy Director, Integrated Certificate Management Division, Aircraft Certification Service. [FR Doc. 2024-24466 Filed 10-23-24; 8:45 am]BILLING CODE 4910-13-P