2024-14-07: Time Limits/Maintenance Checks

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2024-14-07 Airbus SAS: Amendment 39-22788; Docket No. FAA-2024-1286; Project Identifier MCAI-2024-00017-T. (a) Effective Date This airworthiness directive (AD) is effective September 25, 2024. (b) Affected ADs This AD affects AD 2018-18-21, Amendment 39-19400 (83 FR 47054, September 18, 2018) (AD 2018-18-21). (c) Applicability This AD applies to all Airbus SAS airplanes identified in paragraphs (c)(1) through (4) of this AD, certificated in any category. (1) Model A300 B4-601, B4-603, B4-620, and B4-622 airplanes. (2) Model A300 B4-605R and B4-622R airplanes. (3) Model A300 F4-605R and F4-622R airplanes. (4) Model A300 C4-605R Variant F airplanes. (d) Subject Air Transport Association (ATA) of America Code 05, Time Limits/Maintenance Checks. (e) Unsafe Condition This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. The FAA is issuing this AD to address the risks associated with the effects of aging on airplane systems. The unsafe condition, if not addressed, could result in an increased potential for failure of certain life-limited parts, and reduced structural integrity or controllability of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2024-0003, dated January 5, 2024 (EASA AD 2024-0003). (h) Exceptions to EASA AD EASA AD 2024-0003 (1) This AD does not adopt the requirements specified in paragraphs (1) and (2) of EASA AD 2024-0003. (2) Paragraph (3) of EASA AD 2024-0003 specifies revising "the approved AMP," within 12 months after its effective date, but this AD requires revising the existing maintenance or inspection program, as applicable, within 90 days after the effective date of this AD. (3) The initial compliance time for doing the tasks specified in paragraph (3) of EASA AD 2024-0003 is at the applicable "limitations" and "associated thresholds" as incorporated by the requirements of paragraph (3) of EASA AD 2024-0003, or within 90 days after the effective date of this AD, whichever occurs later. (4) This AD does not adopt the provisions specified in paragraph (4) of EASA AD 2024-0003. (5) This AD does not adopt the "Remarks" section of EASA AD 2024-0003. (i) Provisions for Alternative Actions and Intervals After the existing maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions ( e.g., inspections) and intervals are allowed unless they are approved as specified in the provisions of the "Ref. Publications" section of EASA AD 2024-0003. (j) Terminating Action for Certain Tasks Required by AD 2018-18-21 For Model A300 B4-601, B4-603, B4-620, B4-622, B4-605R, B4-622R, 300 F4-605R, F4-622R, and A300 C4-605R Variant F airplanes only: Accomplishing the actions required by this AD terminates the corresponding requirements of AD 2018-18-21 for the tasks identified in the service information referenced in EASA AD 2017-0202 only. (k) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the International Validation Branch, mail it to the address identified in paragraph (l) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (l) Additional Information For more information about this AD, contact Dan Rodina, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 206-231-3225; email: dan.rodina@faa.gov. (m) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this material as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2024-0003, dated January 5, 2024. (ii) [Reserved] (3) For EASA AD 2024-0003, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu; website easa.europa.eu. You may find this EASA AD on the EASA website at ad.easa.europa.eu. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations, or email fr.inspection@nara.gov. Issued on July 12, 2024. Suzanne Masterson, Deputy Director, Integrated Certificate Management Division, Aircraft Certification Service. [FR Doc. 2024-18633 Filed 8-20-24; 8:45 am]BILLING CODE 4910-13-P