2022-25-11: Time Limits/Maintenance Checks

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2022-25-11 Airbus SAS: Amendment 39-22267; Docket No. FAA-2022-1569; Project Identifier MCAI-2022-01267-T. (a) Effective Date This airworthiness directive (AD) is effective January 6, 2023. (b) Affected ADs This AD affects AD 2019-20-06, Amendment 39-19759 (84 FR 55859, October 18, 2019) (AD 2019-20-06). (c) Applicability This AD applies to all Airbus SAS Model A310-203, -204, -221, -222, -304, -322, -324 and -325 airplanes, certificated in any category. (d) Subject Air Transport Association (ATA) of America Code: 05, Time Limits/Maintenance Checks. (e) Unsafe Condition This AD was prompted by a determination that new or more restrictive airworthiness tasks are necessary. The FAA is issuing this AD to address fatigue cracking, damage, or corrosion in principal structural elements. The unsafe condition, if not addressed, could result in reduced structural integrity of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2022-0193, dated September 23, 2022 (EASA AD 2022-0193). (h) Exceptions to EASA AD 2022-0193 (1) The requirements specified in paragraphs (1) and (2) of EASA AD 2022-0193 do not apply to this AD. (2) Paragraph (3) of EASA AD 2022-0193 specifies revising "the approved AMP" within 12 months after its effective date, but this AD requires revising the existing maintenance or inspection program, as applicable, within 90 days after the effective date of this AD. (3) The initial compliance time for doing the tasks specified in paragraph (1) of EASA AD 2022-0193 is at the applicable "associated thresholds" as incorporated by the requirements of paragraph (3) of EASA AD 2022-0193, or within 90 days after the effective date of this AD, whichever occurs later. (4) The provisions specified in paragraph (4) of EASA AD 2022-0193 do not apply to this AD. (5) This AD does not adopt the "Remarks" paragraph of EASA AD 2022-0193. (i) Provisions for Alternative Actions and Intervals After the existing maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions ( e.g., inspections) and intervals are allowed unless they are approved as specified in the provisions of the "Ref. Publications" section of EASA AD 2022-0193. (j) Terminating Action for AD 2019-20-06 Accomplishing the actions required by this AD terminates the corresponding requirements of AD 2019-20-06 only for the tasks identified in the service information referenced in EASA AD 2022-0193. (k) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the Large Aircraft Section, send it to the attention of the person identified in paragraph (l) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (3) Required for Compliance (RC): Except as required by paragraph (k)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (l) Additional Information For more information about this AD, contact Dan Rodina, Aerospace Engineer, Large Aircraft Section, FAA, International Validation Branch, 2200 South 216th St., Des Moines, WA 98198; telephone (206) 231-3225; email [email protected]. (m) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2022-0193, dated September 23, 2022. (ii) [Reserved] (3) For EASA AD 2022-0193, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email [email protected]; website easa.europa.eu. You may find this EASA AD on the EASA website at ad.easa.europa.eu. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call (206) 231-3195. (5) You may view this material that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email [email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html. Issued on November 29, 2022. Christina Underwood, Acting Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2022-27686 Filed 12-21-22; 8:45 am]BILLING CODE 4910-13-P