2022-16-06: Flight Controls

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2022-16-06 Airbus SAS: Amendment 39-22135; Docket No. FAA-2022-0522; Project Identifier MCAI-2022-00340-T. (a) Effective Date This airworthiness directive (AD) is effective September 27, 2022. (b) Affected ADs None. (c) Applicability This AD applies to Airbus SAS airplanes specified in paragraphs (c)(1) and (2) of this AD, certificated in any category, as identified in European Union Aviation Safety Agency (EASA) AD 2022-0039, dated March 8, 2022 (EASA AD 2022-0039). (1) Model A330-201, -202, -203, -223, -223F, -243, -243F, -301, -302, -303, -321, -322, -323, -341, -342, -343, and -941 airplanes. (2) Model A340-211, -212, -213, -311, -312, and -313 airplanes. (d) Subject Air Transport Association (ATA) of America Code 27, Flight Controls. (e) Unsafe Condition This proposed AD was prompted by recent tests that demonstrated that when the upper secondary load path (SLP) of the trimmable horizontal stabilizer actuator (THSA) is engaged, the THSA might not stall, with consequently no indication of SLP engagement. The FAA is issuing this AD to prevent damage on the upper THSA SLP attachment, with consequent mechanical disconnection of the THSA, possibly resulting in loss of control of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2022-0039. (h) Exceptions to EASA AD 2022-0039 (1) Where EASA AD 2022-0039 refers to its effective date, this AD requires using the effective date of this AD. (2) The "Remarks" section of EASA AD 2022-0039 does not apply to this AD. (i) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (j) Related Information For information about this AD, contact Vladimir Ulyanov, Aerospace Engineer, Large Aircraft Section, FAA, International Validation Branch, 2200 South 216th St., Des Moines, WA 98198; telephone 206-231-3229; email Vladimir.Ulyanov@faa.gov. (k) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2022-0039, dated March 8, 2022. (ii) [Reserved] (3) For the service information identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu; internet www.easa.europa.eu. You may find this EASA AD on the EASA website at ad.easa.europa.eu. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email fr.inspection@nara.gov, or go to: www.archives.gov/federal-register/cfr/ibr-locations.html. Issued on July 28, 2022. Christina Underwood, Acting Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2022-18112 Filed 8-22-22; 8:45 am]BILLING CODE 4910-13-P