2022-01-08: Hydraulic power

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2022-01-08 Airbus SAS: Amendment 39-21896; Docket No. FAA-2021-0668; Project Identifier MCAI-2021-00457-T. (a) Effective Date This airworthiness directive (AD) is effective March 8, 2022. (b) Affected ADs None. (c) Applicability This AD applies to all Airbus SAS airplanes identified in paragraphs (c)(1) through (6) of this AD, certificated in any category. (1) Model A300 B2-1A, B2-1C, B2K-3C, B2-203, B4-2C, B4-103, and B4-203 airplanes. (2) Model A300 B4-601, B4-603, B4-620, and B4-622 airplanes. (3) Model A300 B4-605R and B4-622R airplanes. (4) Model A300 C4-605R Variant F airplanes. (5) Model A300 F4-605R and F4-622R airplanes. (6) Model A310-203, -204, -221, -222, -304, -322, -324, and -325 airplanes. (d) Subject Air Transport Association (ATA) of America Code 29, Hydraulic power. (e) Reason This AD was prompted by reports of incorrect installation of the fire shut-off valves (FSOV) actuator, which was found to rotate around its pivot axis. The FAA is issuing this AD to address incorrect installation of the FSOV actuator. This condition, if not addressed, could lead to FSOV failure, and consequent risk of a temporary uncontrolled engine fire, possibly resulting in damage to, and reduced control of, the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2021-0106, dated April 15, 2021 (EASA AD 2021-0106). (h) Exceptions to EASA AD 2021-0106 (1) Where EASA AD 2021-0106 refers to its effective date, this AD requires using the effective date of this AD. (2) The "Remarks" section of EASA AD 2021-0106 does not apply to this AD. (3) Paragraph (4) of EASA AD 2021-0106 specifies to report inspection results to Airbus within a certain compliance time. For this AD, report inspection results at the applicable time specified in paragraph (h)(3)(i) or (ii) of this AD. (i) If the inspection was done on or after the effective date of this AD: Submit the report within 30 days after the inspection. (ii) If the inspection was done before the effective date of this AD: Submit the report within 30 days after the effective date of this AD. (4) Where the service information referenced in EASA AD 2021-0106 specifies to send the FSOV actuator for repair if it moves (rotates around its pivot axis) during the inspection, this AD requires replacing any FSOV actuator that moves (rotates around its pivot axis) during the inspection with a serviceable actuator, as specified in EASA AD 2021-0106. (i) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (j) Related Information For more information about this AD, contact Dan Rodina, Aerospace Engineer, Large Aircraft Section, International Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3225; email [email protected]. (k) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2021-0106, dated April 15, 2021. (ii) [Reserved] (3) For EASA AD 2021-0106, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email [email protected] ; internet www.easa.europa.eu. You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email [email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html. Issued on December 29, 2021. Lance T. Gant, Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2022-01961 Filed 1-31-22; 8:45 am]BILLING CODE 4910-13-P