2019-21-10: Wings

Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39--AIRWORTHINESS DIRECTIVES 0 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. Sec. 39.13 [Amended] 0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): 2019-21-10 Airbus SAS: Amendment 39-19776; Docket No. FAA-2019-0400; Product Identifier 2019-NM-022-AD. (a) Effective Date This AD is effective December 24, 2019. (b) Affected ADs None. (c) Applicability This AD applies to all Airbus SAS Model A321-111, A321-112, A321-131, A321-211, A321-212, A321-213, A321-231, and A321-232 airplanes, certificated in any category. (d) Subject Air Transport Association (ATA) of America Code 57, Wings. (e) Reason This AD was prompted by a quality control review, which determined that the wrong aluminum alloy was used to manufacture several structural parts. The FAA is issuing this AD to address structural parts made of incorrect aluminum alloy, which could result in reduced structural integrity of the outer flaps and reduced controllability of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Aviation Safety Agency (EASA) AD 2019- 0012, dated January 24, 2019 (``EASA AD 2019-0012''). (h) Exceptions to EASA AD 2019-0012 (1) Where EASA AD 2019-0012 refers to its effective date, this AD requires using the effective date of this AD. (2) The ``Remarks'' section of EASA AD 2019-0012 does not apply to this AD. (3) Where paragraph (5) of EASA AD 2019-0012 mandates a parts installation limitation, this AD requires the following parts installation limitation: From the effective date of this AD, only serviceable parts as defined in EASA AD 2019-0012 are allowed to be installed on any airplane. (4) Where any service information referenced in EASA AD 2019- 0012 specifies reporting, this AD requires reporting all inspection results at the applicable time specified in paragraph (h)(4)(i) or (ii) of this AD. If operators have reported findings as part of obtaining any corrective actions approved by Airbus SAS's EASA Design Organization Approval (DOA), operators are not required to report those findings as specified in this paragraph. (i) If the inspection was done on or after the effective date of this AD: Submit the report within 30 days after the inspection. (ii) If the inspection was done before the effective date of this AD: Submit the report within 90 days after the effective date of this AD. (i) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found [[Page 63797]] in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS's EASA DOA. If approved by the DOA, the approval must include the DOA- authorized signature. (3) Required for Compliance (RC): For any service information referenced in EASA AD 2019-0012 that contains RC procedures and tests: Except as required by paragraphs (h)(4) and (i)(2) of this AD, RC procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (4) Paperwork Reduction Act Burden Statement: A federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to a penalty for failure to comply with a collection of information subject to the requirements of the Paperwork Reduction Act unless that collection of information displays a current valid OMB Control Number. The OMB Control Number for this information collection is 2120-0056. Public reporting for this collection of information is estimated to be approximately 1 hour per response, including the time for reviewing instructions, completing and reviewing the collection of information. All responses to this collection of information are mandatory as required by this AD; the nature and extent of confidentiality to be provided, if any. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden to Information Collection Clearance Officer, Federal Aviation Administration, 10101 Hillwood Parkway, Fort Worth, TX 76177-1524. (j) Related Information For more information about this AD, contact Sanjay Ralhan, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3223. (k) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Aviation Safety Agency (EASA) AD 2019-0012, dated January 24, 2019. (ii) [Reserved] (3) For information about EASA AD 2019-0012, contact the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 89990 6017; email [email protected]; Internet www.easa.europa.eu. You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. (4)You may view this material at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. This material may be found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA- 2019-0400. (5) You may view this material that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email [email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.