2017-22-10: Equipment/furnishings

Adoption of the Amendment \n\n\n\tAccordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: \n\nPART 39--AIRWORTHINESS DIRECTIVES \n\n0 1. The authority citation for part 39 continues to read as follows: \n\n\n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\nSec. 39.13 (Amended) \n\n0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): \n\n2017-22-10 The Boeing Company: Amendment 39-19090; Docket No. FAA- 2017-0499; Product Identifier 2016-NM-205-AD. \n\n(a) Effective Date \n\n\n\tThis AD is effective December 29, 2017. \n\n(b) Affected ADs \n\n\n\tNone. \n\n(c) Applicability \n\n\n\tThis AD applies to The Boeing Company Model 747-400, 747-400F, and 747-8F series airplanes, certificated in any category, as identified in Boeing Special Attention Service Bulletin 747-25-3693, dated November 10, 2016. \n\n(d) Subject \n\n\n\tAir Transport Association (ATA) of America Code 25; Equipment/ furnishings.(e) Unsafe Condition \n\n\n\tThis AD was prompted by reports of failure of the fastener assemblies on the crew access ladder handrails. We are issuing this AD to prevent the fastener assemblies from coming loose on the crew access ladder handrails, which could result in serious or fatal injury to personnel. \n\n(f) Compliance \n\n\n\tComply with this AD within the compliance times specified, unless already done. \n\n(g) Replacement \n\n\n\tWithin 36 months after the effective date of this AD, replace the fastener assemblies in the crew access ladder handrails with new fastener assemblies, in accordance with the Accomplishment Instructions of Boeing Special Attention Service Bulletin 747-25- 3693, dated November 10, 2016. \n\n(h) Parts Installation Limitation \n\n\n\tAs of the effective date of this AD, no person may install the discrepant fastener hardware identified in the Accomplishment Instructions of Boeing Special Attention Service Bulletin 747-25- 3693, dated November 10, 2016, ona crew access ladder on any airplane. \n\n(i) Alternative Methods of Compliance (AMOCs) \n\n\n\t(1) The Manager, Seattle ACO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the certification office, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: [email protected]. \n\t(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. \n\t(3) An AMOC that provides an acceptable level of safety may be used for any repair, modification, or alteration required by this AD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) that has been authorized by the Manager, Seattle ACO Branch, to make those findings. To be approved, the repair method, modification deviation, or alteration deviation must meet the certification basis of the airplane, and the approval must specifically refer to this AD. \n\t(4) For service information that contains steps that are labeled as Required for Compliance (RC), the provisions of paragraphs (i)(4)(i) and (i)(4)(ii) of this AD apply. \n\t(i) The steps labeled as RC, including substeps under an RC step and any figures identified in an RC step, must be done to comply with the AD. If a step or substep is labeled ''RC Exempt,'' then the RC requirement is removed from that step or substep. An AMOC is required for any deviations to RC steps, including substeps and identified figures. \n\t(ii) Steps not labeled as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program withoutobtaining approval of an AMOC, provided the RC steps, including substeps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition. \n\n(j) Related Information \n\n\n\tFor more information about this AD, contact Susan L. Monroe, Aerospace Engineer, Cabin Safety and Environmental Systems Section, FAA, Seattle ACO Branch, 1601 Lind Avenue SW., Renton, WA; phone: 425-917-6457; fax: 425-917-6590; email: [email protected]. \n\n(k) Material Incorporated by Reference \n\n\n\t(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. \n\t(2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. \n\t(i) Boeing Special Attention Service Bulletin 747-25-3693, dated November 10, 2016. \n\t(ii) Reserved. \n\n((Page 55760)) \n\n\n\t(3) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740- 5600; telephone 562-797-1717; Internet https://www.myboeingfleet.com. \n\t(4) You may view this service information at the FAA, Transport Standards Branch, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221. \n\t(5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.