2017-21-07: Navigation

Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, [[Page 48909]] the FAA amends 14 CFR part 39 as follows: PART 39--AIRWORTHINESS DIRECTIVES 0 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. Sec. 39.13 [Amended] 0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): 2017-21-07 Airbus: Amendment 39-19078; Docket No. FAA-2017-0497; Product Identifier 2016-NM-209-AD. (a) Effective Date This AD is effective November 27, 2017. (b) Effective Date None. (c) Applicability This AD applies to Airbus Model A300 B2-1A, B2-1C, B2K-3C, B2- 203, B4-2C, B4-103, and B4-203 airplanes, certificated in any category, all manufacturer serial numbers. (d) Subject Air Transport Association (ATA) of America Code 34, Navigation. (e) Reason This AD was prompted by areport of reduction of the de-icing performance of the pitot probe over time that could remain hidden to the flight crew. We are issuing this AD to ensure nominal de-icing performance of the pitot probe in order to prevent unreliable airspeed indications, which could result in reduced control of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Definition of Pitot Probes For the purpose of this AD, affected pitot probes are the First Officer's Pitot Probe 40DA, Captain's Pitot Probe 41DA, and Standby Pitot Probe 42DA. (h) Repetitive Inspections At the time specified in paragraph (h)(1) or (h)(2) of this AD, whichever occurs later, do a detailed inspection of the pitot probe heater insulation resistance on each affected pitot probe, in accordance with the Accomplishment Instructions of Airbus Service Bulletin A300-34-0185, Revision 00, dated August 29, 2016. Repeat the inspection thereafter at intervals not to exceed 24 months. (1) Within 24 months since the last detailed inspection of the pitot probe heater insulation resistance, as specified in Airbus A300 Aircraft Maintenance Manual (AMM), Task 30-31-00, Insulation Test of Pitot Heater Resistance. (2) Within 6 months after the effective date of this AD. (i) Corrective Action If, during any detailed inspection as required by paragraph (h) of this AD, any pitot probe fails the test, as specified in the Accomplishment Instructions of Airbus Service Bulletin A300-34-0185, Revision 00, dated August 29, 2016, before further flight, replace the affected pitot probe with a serviceable (new or inspected as required by this AD) pitot probe, in accordance with the Accomplishment Instructions of Airbus Service Bulletin A300-34-0185, Revision 00, dated August 29, 2016. Replacement of pitot probes, as required by this paragraph, does not constitute terminating action for the repetitive inspections required by paragraph (h) of this AD. (j) Reporting At the applicable times required by paragraph (j)(1) or (j)(2) of this AD: Submit a report of the findings (both positive and negative) of each inspection required by paragraph (h) of this AD, as specified in the Accomplishment Instructions of Airbus Service Bulletin A300-34-0185, Revision 00, dated August 29, 2016, to Airbus Service Bulletin Reporting Online Application on Airbus World (https://w3.airbus.com/). (1) For inspections done before the effective date of this AD: Within 30 days after the effective date of this AD. (2) For inspections done on or after the effective date of this AD: Within 30 days after accomplishing each inspection required by paragraph (h) of this AD. (k) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (l)(2) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or the European Aviation Safety Agency (EASA); or Airbus's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include theDOA- authorized signature. (3) Reporting Requirements: A federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to a penalty for failure to comply with a collection of information subject to the requirements of the Paperwork Reduction Act unless that collection of information displays a current valid OMB Control Number. The OMB Control Number for this information collection is 2120-0056. Public reporting for this collection of information is estimated to be approximately 5 minutes per response, including the time for reviewing instructions, completing and reviewing the collection of information. All responses to this collection of information are mandatory. Comments concerning the accuracy of this burden and suggestions for reducing the burden should be directed to the FAA at: 800 Independence Ave. SW., Washington, DC 20591, Attn: Information Collection Clearance Officer, AES-200. (4) Required for Compliance (RC): Except as required by paragraph (j) of this AD: If any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (l) Related Information (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA AD 2016-0248, dated December 15, 2016, for related information. This MCAI may be found in the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2017-0497. (2) For more information about this AD, contact Dan Rodina, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; telephone: 425-227-2125; fax: 425-227-1149. (3) Service information identified in this AD that is not incorporated by reference is available at the addresses specified in paragraphs (m)(3) and (m)(4) of this AD. (m) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) Airbus Service Bulletin A300-34-0185, Revision 00, dated August 29, 2016. (ii) Reserved. (3) For service information identified in this AD, contact Airbus SAS, Airworthiness Office--EAW, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France; telephone: +33 5 61 93 36 96; fax: +33 5 61 93 44 51; email: [email protected]; Internet: http://www.airbus.com. (4) You may view this service information at the FAA, Transport Standards Branch, 1601 Lind Avenue SW., Renton, WA. For [[Page 48910]] information on the availability of this material at the FAA, call 425-227-1221. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.