2016-24-02: Wings

Adoption of the Amendment \n\n\n\tAccordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: \n\nPART 39--AIRWORTHINESS DIRECTIVES \n\n0 1. The authority citation for part 39 continues to read as follows: \n\n\n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\n\n\nSec. 39.13 (Amended) \n\n0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): \n\n2016-24-02 The Boeing Company: Amendment 39-18719; Docket No. FAA- 2016-5041; Directorate Identifier 2015-NM-102-AD. \n\n(a) Effective Date \n\n\n\tThis AD is effective December 30, 2016. \n\n(b) Affected ADs \n\n\n\tNone. \n\n(c) Applicability \n\n\n\tThis AD applies to The Boeing Company Model 747-8 and 747-8F series airplanes, certificated in any category, as identified in Boeing Alert Service Bulletin 747-57A2348, Revision 1, dated February 26, 2016; except for line numbers 1435, 1506, and 1509, which were delivered with the terminating action already incorporated and are not affected by this AD. \n\n(d) Subject \n\n\n\tAir Transport Association (ATA) of America Code 57, Wings. \n\n(e) Unsafe Condition \n\n\n\tThis AD was prompted by a report that static strength analysis has shown that the aluminum transmission aft bearing plate assemblies have inadequate structural strength for one or more of the required load cases, including cases for drive system jam, flap skew, and structural damage tolerance. Inadequate structural strength can result in damage to the transmission aft bearing plate assemblies. We are issuing this AD to prevent inadequate structural strength of transmission aft bearing plate assemblies. This condition could result in damaged transmission aft bearing plate assemblies, which could result in incorrect operation and departure of the flap from the airplane and consequent loss of controllability of the airplane. \n\n(f) Compliance \n\n\n\tComply with this AD within the compliance times specified, unless already done. \n\n(g) Replacement \n\n\n\tWithin 48 months after the effective date of this AD: Remove aluminum transmission aft bearing plate assemblies from the flap track and install new titanium transmission aft bearing plate assemblies to the flap track, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 747-57A2348, Revision 1, dated February 26, 2016. \n\n(h) Credit for Previous Actions \n\n\n\tThis paragraph provides credit for the actions specified in paragraph (g) of this AD, if those actions were performed before the effective date of this AD using Boeing Alert Service Bulletin 747- 57A2348, dated June 12, 2015. \n\n(i) Alternative Methods of Compliance (AMOCs) \n\n\n\t(1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in paragraph (j)(1) of this AD. Information may be emailed to: [email protected]. \n\t(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. \n\t(3) An AMOC that provides an acceptable level of safety may be used for any repair, modification, or alteration required by this \n\n((Page 85121)) \n\nAD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) that has been authorized by the Manager, Seattle ACO, to make those findings. To be approved, the repair method, modification deviation, or alteration deviation must meet the certification basis of the airplane, and the approval must specifically refer to this AD. \n\t(4) For service information that containssteps that are labeled as Required for Compliance (RC), the provisions of paragraphs (i)(4)(i) and (i)(4)(ii) of this AD apply. \n\t(i) The steps labeled as RC, including substeps under an RC step and any figures identified in an RC step, must be done to comply with the AD. If a step or substep is labeled ''RC Exempt,'' then the RC requirement is removed from that step or substep. An AMOC is required for any deviations to RC steps, including substeps and identified figures. \n\t(ii) Steps not labeled as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the RC steps, including substeps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition. \n\n(j) Related Information \n\n\n\t(1) For more information about this AD, contact Bill Ashforth, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle ACO, 1601 Lind AvenueSW., Renton, WA 98057-3356; phone: 425-917-6432; fax: 425-917-6590; email: [email protected]. \n\t(2) Service information identified in this AD that is not incorporated by reference is available at the addresses specified in paragraphs (k)(3) and (k)(4) of this AD. \n\n(k) Material Incorporated by Reference \n\n\n\t(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. \n\t(2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. \n\t(i) Boeing Alert Service Bulletin 747-57A2348, Revision 1, dated February 26, 2016. \n\t(ii) Reserved. \n\t(3) For Boeing service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. \n\t(4) You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221. \n\t(5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.