2013-22-17: Aerodynamic Fairings

Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39--AIRWORTHINESS DIRECTIVES 0 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. Sec. 39.13 [Amended] 0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): 2013-22-17 Eurocopter France: Amendment 39-17649; Docket No. FAA- 2013-0479; Directorate Identifier 2011-SW-070-AD. (a) Applicability This AD applies to Eurocopter France (Eurocopter) Model AS332C, AS332L, AS332L1, AS332L2, and EC225LP helicopters with an intermediate gearbox (IGB) fairing, part number (P/N) 332A24-0303- 0501, P/N 332A24-0303-0601, P/N 332A081391.00, or P/N 332A081391.01 installed, certificated in any category. (b) Unsafe Condition This AD defines the unsafe condition as a crack in the IGB fairing, which could resultin separation of the IGB fairing from its attachment supports, resulting in interference with the tail rotor (T/R) inclined driveshaft, failure of the T/R inclined driveshaft, and subsequent loss of control of the helicopter. (c) Effective Date This AD becomes effective December 9, 2013. (d) Compliance You are responsible for performing each action required by this AD within the specified compliance time unless it has already been accomplished prior to that time. (e) Required Actions Within 15 hours time-in-service (TIS), and thereafter at intervals not to exceed 15 hours TIS: (1) For all helicopters, inspect the IGB fairing and both attachment supports for a crack. If there is a crack, replace the cracked part with an airworthy part. (2) For helicopters with an IGB fairing, part number (P/N) 332A24-0303-0501 or P/N 332A24-0303-0601, installed, inspect the IGB fairing gutter (gutter) for a crack. If there is a crack, replace the gutter with an airworthy gutter, and inspect the IGB fairing for separation, or interference between the gutter and the T/R inclined drive shaft, hydraulic pipes, or flight controls. (i) If there is interference between the gutter and the T/R inclined drive shaft tube, replace the T/R inclined drive shaft tube and the IGB fairing/gutter assembly with an airworthy T/R inclined drive shaft tube and IGB fairing/gutter assembly. (ii) If there is interference between the gutter and the hydraulic pipes, replace the IGB fairing/gutter assembly with an airworthy IGB fairing/gutter assembly. Inspect the hydraulic pipes for a dent, score, distortion, or chafing. If there is a dent, score, distortion, or chafing, replace the affected hydraulic pipe with an airworthy hydraulic pipe. (iii) If there is interference between the gutter and the flight controls, replace the IGB fairing/gutter assembly with an airworthy IGB fairing/gutter assembly. Inspect the cables on the left hand side of the pylon, the quadrant on which the cables are coiled, the flight control lever, the rod, and the T/R servo-control operating mechanism for friction, chafing, broken strands, buckling, distortion, or scoring. If there is any friction, chafing, broken strands, buckling, distortion, or scoring, replace the affected flight control component with an airworthy flight control component. (iv) If there is any separation of the gutter, replace the IBG fairing/gutter assembly with an airworthy fairing/gutter assembly. (f) Alternative Methods of Compliance (AMOCs) (1) The Manager, Safety Management Group, FAA, may approve AMOCs for this AD. Send your proposal to: Gary Roach, Aviation Safety Engineer, Regulations and Policy Group, Rotorcraft Directorate, FAA, 2601 Meacham Blvd., Fort Worth, Texas 76137; telephone (817) 222- 5110; email [email protected]. (2) For operations conducted under a 14 CFR part 119 operating certificate or under 14 CFR part 91, subpart K, we suggest that you notify your principal inspector, or lacking a principal inspector, the manager of the local flight standards district office or certificate holding district office, before operating any aircraft complying with this AD through an AMOC. (g) Additional Information (1) Eurocopter Emergency Alert Service Bulletin (EASB) No. 53.01.47 for Model AS 332 helicopters, EASB No. 53.00.48 for Model AS532 helicopters, and EASB No. 53A001 for Model EC225 and EC725 helicopters, all revision 4, dated September 27, 2011, which are not incorporated by reference, contain additional information about the subject of this AD. For service information identified in this AD, contact American Eurocopter Corporation, 2701 N. Forum Drive, Grand Prairie, TX 75052; telephone (972) 641-0000 or (800) 232-0323; fax (972) 641-3775; or at http://www.eurocopter.com/techpub. You may review a copy of the service information at the FAA, Office of the Regional Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas 76137. (2) The subject of this AD is addressed in European Aviation Safety Agency (EASA) Emergency AD No. 2011-0189-E, dated September 29, 2011. You may view the EASA AD on the internet in Docket No. FAA-2013-0479 at http://www.regulations.gov. (h) Subject Joint Aircraft Service Component (JASC) Code: 5350: Aerodynamic Fairings.