Show the full text (6,788 characters)
2007-19-19 Boeing: Docket No. FAA-2007-29263; Directorate Identifier 2007-NM-198-AD; Amendment 39-15210. \n\nEffective Date \n\n\t(a) This AD becomes effective October 9, 2007. \n\nAffected ADs \n\n\t(b) This AD supersedes AD 2001-15-02. \n\nApplicability \n\n\t(c) This AD applies to Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747SR, and 747SP series airplanes, certificated in any category; as identified in Boeing Alert Service Bulletin 747-54A2203, Revision 1, dated August 9, 2007. \n\nUnsafe Condition \n\n\t(d) This AD results from new reports of under-torqued or loose fasteners, a cracked bulkhead chord, and a fractured back-up angle after operators accomplished the terminating action required by the existing AD. We are issuing this AD to detect and correct loose fasteners and/or damaged or cracked hanger fittings, back-up angles, and bulkhead of the forward engine mount, which could lead to failure of the hanger fitting and bulkhead and consequent separation of the engine from the airplane. \n\nCompliance \n\n\t(e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. \n\nCertain Requirement of AD 2001-15-02 \n\n\t(f) Within 60 months after August 24, 2001 (the effective date of AD 2001-15-02): Accomplish all actions specified in Part 6 of the Accomplishment Instructions of Boeing Alert Service Bulletin 747- 54A2203, dated August 31, 2000. Where the alert service bulletin specifies that the manufacturer may be contacted for disposition of certain corrective actions (rework or replacement of fittings), this AD requires such rework and/or replacement to be done in accordance with a method approved by the Manager, Seattle Aircraft Certification Office (ACO); or in accordance with data meeting the type certification basis of the airplane approved by a Boeing Company Designated Engineering Representative (DER) who has been authorized by the Manager, Seattle ACO, to make such findings. For a repair method to be approved by the Manager, Seattle ACO, as required by this paragraph, the Manager's approval letter must specifically reference this AD. As of the effective date of this AD, the rework and/or replacement must be done using a method approved in accordance with the procedures specified in paragraph (k) of this AD. \n\n\tNote 1: Installation of two BACW10BP*APU washers on Group A fasteners accomplished during modification in accordance with Boeing Service Bulletin 747-54A2159, dated November 3, 1994, Revision 1, dated June 1, 1995, or Revision 2, dated March 14, 1996; and pin or bolt protrusion as specified in the 747 Structural Repair Manual, Chapter 51-30-02 (both referenced in Boeing Alert Service Bulletin 747-54A2203, dated August 31, 2000); is considered acceptable for compliance with the action required by paragraph (f) of this AD. \n\nNew Actions Required by This AD \n\nInspections and Related Investigative and Corrective Actions \n\n\t(g) Except as provided by paragraphs (i) and (j) of this AD: At the applicable compliance times and repeat intervals listed in Tables 1 and 2 of paragraph 1.E., "Compliance,'' of Boeing Alert Service Bulletin 747-54A2203, Revision 1, dated August 9, 2007, do the inspections and applicable related investigative and corrective actions by accomplishing all the actions specified in Parts 2 and 8 of the Accomplishment Instructions of the service bulletin. \n\nOptional Initial and Repetitive Inspections and Related Investigative and Corrective Actions \n\n\t(h) Do the initial and repetitive inspections and related investigative and corrective actions by accomplishing all the actions specified in Part 7 of the Accomplishment Instructions of Boeing Alert Service Bulletin 747-54A2203, Revision 1, dated August 9, 2007, except as provided by paragraph (j) of this AD. \n\nExceptions to Service Bulletin \n\n\t(i) Where Boeing Alert Service Bulletin 747-54A2203, Revision 1, dated August 9, 2007, specifies a compliance time after the date of the service bulletin, this AD requires compliance within the specified compliance time after the effective date of this AD. \n\n\t(j) Where Boeing Alert Service Bulletin 747-54A2203, Revision 1, dated August 9, 2007, specifies to contact Boeing for appropriate action, this AD requires, before further flight, repair of the discrepancy or replacement of the discrepant part using a method approved in accordance with the procedures specified in paragraph (k) of this AD. \n\nAlternative Methods of Compliance (AMOCs) \n\n\t(k)(1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19. \n\t(2) To request a different method of compliance or a different compliance time for this AD, follow the procedures in 14 CFR 39.19. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. \n\t(3) An AMOC that provides an acceptable level of safety may be used for any repair required by this AD, if it is approved by an Authorized Representative for the Boeing Commercial Airplanes Delegation Option Authorization Organization who has been authorized by the Manager, Seattle ACO, to make those findings. For a repair method to be approved, the repair must meet the certification basis of the airplane, and the approval must specifically refer to this AD. \n\nMaterial Incorporated by Reference \n\n\t(l) You must use Boeing Alert Service Bulletin 747-54A2203, dated August 31, 2000; and Boeing Alert Service Bulletin 747- 54A2203, Revision 1, dated August 9, 2007; to perform the actions that are required by this AD, unless the AD specifies otherwise. \n\t(1) The Director of the Federal Register approved the incorporation by reference of Boeing Alert Service Bulletin 747- 54A2203, Revision 1, dated August 9, 2007, in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. \n\t(2) On December 6, 2000 (65 FR 69862, November 21, 2000), the Director of the Federal Register approved the incorporation by reference of Boeing Alert Service Bulletin 747-54A2203, dated August 31, 2000. \n\t(3) Contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124-2207, for a copy of this service information. You may review copies at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.
