2000-08-11: Life-limited Parts

2000-08-11 General Electric Company: Amendment 39-11697. Docket No. 98-ANE-41-AD. Supersedes AD 99-08-18, Amendment 39-11124. Applicable Engines General Electric Company (GE) CF6-6, CF6-45, and CF6-50 series turbofan engines, installed on but not limited to Airbus Industrie A300 series, Boeing 747 series, and McDonnell Douglas DC-10 series airplanes. Note 1: This airworthiness directive (AD) applies to each engine identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For engines that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (c) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD;and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it. Compliance Required as indicated, unless accomplished previously. To prevent critical life-limited rotating engine part failure, which could result in an uncontained engine failure and damage to the airplane, accomplish the following: Inspections (a) Within the next 30 days after the effective date of this AD, revise the manufacturer's Time Limitations Section of the Instructions for Continued Airworthiness (ICA), and for air carrier operations revise the approved continuous airworthiness maintenance program, by adding the following: " MANDATORY INSPECTIONS (1) Perform inspections of the following parts at each piece-part opportunity in accordance with the instructions provided in the applicable manual provisions: Part Nomenclature Part number (P/N) Inspect per Engine Shop Manual Chapter For CF6-6 Engines: Disk, Fan RotorStage One All 72-21-03 Paragraph 2.F. or Paragraph 2.A.B. Fluorescent-Penetrant Inspect, and 72-21-03 Paragraph 3 or 3.A. Eddy Current Inspection Disk, HPT Rotor Stage One All 72-53-03 Paragraph 1. Fluorescent-Penetrant Inspect, and 72-53-03 Paragraph 4. Eddy Current Inspection of the HPTR Disk Rim Boltholes and 72-53-03 Paragraph 5. Disk Bore Area Eddy Current Inspection Disk, HPT Rotor Stage Two All 72-53-04 Paragraph 1. Fluorescent-Penetrant Inspect, and Paragraph 4. Eddy Current Inspection of the Stage 2 HPTR Disk Rim Boltholes and 72-53-04 Paragraph 5. Eddy Current Inspection of the Stage 2 Disk Inner Boltholes and 72-53-04 Paragraph 6. Disk Bore Area Eddy Current Inspection Part Nomenclature Part number (P/N) Inspect per Engine Shop Manual Chapter For CF6-45, CF6-50 Engines: Disk, Fan Rotor Stage One All Task 72-21-03-230-051 Fluorescent Penetrant Inspection, and Task 72-21-03-250-002-052 Manual Eddy Current Inspectionor 72-21-03-250-003-053 Automated Eddy Current Inspection Disk, HPT Rotor Stage One All Task 72-53-03-230-001-059 Fluorescent-Penetrant Inspect Disk, and Task 72-53-03-250-052 Eddy Current Inspection of the HPTR Stage 1 Rim Boltholes, and Task 72-53-03-250-060, Disk Bore Area Eddy Current Inspection Disk, HPT Rotor Stage Two All Task 72-53-04-230-001-057 Fluorescent-Penetrant Inspect Disk, and Task 72-53-04-250-053 Eddy Current Inspection of the HPTR Stage 2 Rim and/or Inner Boltholes, and Task 72-53-04-250-060, Disk Bore Area Eddy Current Inspection (2) For the purposes of these mandatory inspections, piece-part opportunity means: (i) The part is considered completely disassembled when accomplished in accordance with the disassembly instructions in the manufacturer's engine manual; and (ii) The part has accumulated more than 100 cycles in service since the last piece-part opportunity inspection, provided that the part was not damaged or related to the cause for its removal from the engine." (b) Except as provided in paragraph (c) of this AD, and notwithstanding contrary provisions in section 43.16 of the Federal Aviation Regulations (14 CFR 43.16), these mandatory inspections shall be performed only in accordance with the Time Limits Section of the manufacturer's ICA. Alternative Methods of Compliance (c) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Engine Certification Office (ECO). Operators shall submit their requests through an appropriate FAA Principal Maintenance Inspector, who may add comments and then send it to the ECO. Note 2: Information concerning the existence of approved alternative methods of compliance with this airworthiness directive, if any, may be obtained from the ECO. Ferry Flights (d) Special flight permits may be issued in accordance with sections 21.197 and 21.199 ofthe Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished. Continuous Airworthiness Maintenance Program (e) FAA-certificated air carriers that have an approved continuous airworthiness maintenance program in accordance with the record keeping requirement of 121.369 (c) of the Federal Aviation Regulations [14 CFR 121.369 (c)] must maintain records of the mandatory inspections that result from revising the Time Limits Section of the ICA and the air carrier's continuous airworthiness program. Alternately, certificated air carriers may establish an approved system of record retention that provides a method for preservation and retrieval of the maintenance records that include the inspections resulting from this AD, and include the policy and procedures for implementing this alternate method in the air carrier's maintenance manual required by 121.369 (c) of the Federal Aviation Regulations [14 CFR 121.369 (c)]; however, the alternate system must be accepted by the appropriate PMI and require the maintenance records be maintained either indefinitely or until the work is repeated. Records of the piece-part inspections are not required under 121.380 (a) (2) (vi) of the Federal Aviation Regulations [14 CFR 121.380 (a) (2) (vi)]. All other Operators must maintain the records of mandatory inspections required by the applicable regulations governing their operations. Note 3: The requirements of this AD have been met when the engine shop manual changes are made and air carriers have modified their continuous airworthiness maintenance plans to reflect the requirements in the engine shop manuals. (f) This amendment becomes effective on October 23, 2000.