2019-14-04: Time Limits/Maintenance Checks

Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39--AIRWORTHINESS DIRECTIVES 0 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. Sec. 39.13 [Amended] 0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): 2019-14-04 Airbus SAS: Amendment 39-19682; Docket No. FAA-2019-0116; Product Identifier 2018-NM-152-AD. (a) Effective Date This AD is effective August 29, 2019. (b) Affected ADs This AD affects AD 2018-17-21, Amendment 39-19375 (83 FR 44209, August 30, 2018) (``AD 2018-17-21''). (c) Applicability This AD applies to the Airbus SAS airplanes identified in paragraphs (c)(1) through (c)(4) of this AD, certificated in any category, with an original airworthiness certificate or original export certificate of airworthiness issuedon or before June 13, 2018. (1) Model A318-111, -112, -121, and -122 airplanes. (2) Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes. (3) Model A320-211, -212, -214, -216, -231, -232, -233, -251N, - 252N, and -271N airplanes. (4) Model A321-111, -112, -131, -211, -212, -213, -231, -232, - 251N, -251NX, -252N, -252NX, -253N, -253NX, -271N, -271NX, -272N, and -272NX airplanes. (d) Subject Air Transport Association (ATA) of America Code 05, Time Limits/ Maintenance Checks. (e) Reason This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. The FAA is issuing this AD to address the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Maintenance or Inspection Program Revision Within 90 days after the effective date of this AD, revise the existing maintenance or inspection program, as applicable, to incorporate the information specified in Airbus A318/A319/A320/A321 Airworthiness Limitations Section (ALS), Part 5, Fuel Airworthiness Limitations (FAL), [[Page 35814]] Revision 05, dated June 13, 2018. The initial compliance time for doing the tasks is at the time specified in Airbus A318/A319/A320/ A321 Airworthiness Limitations Section (ALS), Part 5, Fuel Airworthiness Limitations (FAL), Revision 05, dated June 13, 2018, or within 90 days after the effective date of this AD, whichever occurs later. (h) No Alternative Actions, Intervals, or Critical Design Configuration Control Limitations (CDCCLs) After the maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions (e.g., inspections), intervals, or CDCCLs may be used unless the actions, intervals, andCDCCLs are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (j)(1) of this AD. (i) Terminating Action for AD 2018-17-21 Accomplishing the actions required by this AD terminates all requirements of AD 2018-17-21. (j) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (k)(2) of this AD. Information may be emailed to: [email protected]. (i) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (ii) AMOCs approved previously for AD 2018-17-21 are approved as AMOCs for the corresponding provisions of this AD. (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or the European Aviation Safety Agency (EASA); or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (3) Required for Compliance (RC): If any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (k) Related Information (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA AD 2018-0231, dated October 25, 2018, for related information. This MCAI may be found in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-0116. (2) For more information about this AD, contact Sanjay Ralhan, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3223. (l) Material Incorporated by Reference (1) The Director of the FederalRegister approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) Airbus A318/A319/A320/A321 Airworthiness Limitations Section (ALS), Part 5, Fuel Airworthiness Limitations (FAL), Revision 05, dated June 13, 2018. (ii) Reserved (3) For service information identified in this AD, contact Airbus SAS, Airworthiness Office--EIAS, Rond-Point Emile Dewoitine No: 2, 31700 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 44 51; email [email protected]; internet http://www.airbus.com. (4) You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.