98-16-03: Wing Front Attachments

98-16-03 SOCATA - GROUPE AEROSPATIALE: Amendment 39-10677; Docket No. 95-CE-72-AD. Applicability: The following airplane models and serial numbers, certificated in any category: Model TB9, serial numbers 1 through 9999; and Model TB10, serial numbers 1 through 803, 805, 806, 809 through 815, 820, 821, and 822. NOTE 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (g) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it. Compliance: Required as indicated in the body of this AD, unless already accomplished. To prevent structural failure of the wing front attachments caused by fatigue cracking, which could result in the wing separating from the airplane if the airplane is operated with cracked wing front attachments over an extended period of time, accomplish the following: NOTE 2: The compliance times of this AD are presented in landings instead of hours time-in-service (TIS). If the number of landings is unknown, hours TIS may be used by multiplying the number of hours TIS by 1.5. (a) For all affected airplanes, upon accumulating 3,000 landings on the wing front attachments or within the next 100 landings after the effective date of this AD, whichever occurs later, and thereafter at intervals not to exceed 3,000 landings, inspect the wing front attachments (both the wing sides and fuselage sides) in accordancewith Socata Service Bulletin No. SB 10-081-57, Amendment 1, dated August 1996. (b) For all affected airplanes, accomplish the following on the wing front attachments on the wing sides: (1) If no cracks are found on the wing front attachments on the wing sides during any inspection required by paragraph (a) of this AD, upon accumulating 12,000 landings on these wing front attachments or within the next 100 landings after the effective date of this AD, whichever occurs later, and thereafter at intervals not to exceed 6,000 landings provided no cracks are found during any inspection required by paragraph (a) of this AD, incorporate Modification Kit OPT10 911000 in accordance with Socata Technical Instruction No. 9110, which incorporates the following pages: Pages Revision Level Date 0 and 1 Amendment 1 January 31, 1992 2 through 11 Original Issue October 1985 (2) If a crack(s) is found on the wing front attachments on the wing sides during any inspection required by paragraph (a) of this AD, prior to further flight, incorporate Modification Kit OPT10 911000 in accordance with Socata Technical Instruction No. 9110. Incorporate this kit at intervals not to exceed 6,000 landings thereafter provided no cracks are found during any inspection required by paragraph (a) of this AD. (c) For Models TB9 and TB10 airplanes, with a serial number in the range of 1 through 399, or with a serial number of 413; that do not have either Socata Service Letter (SL) 10-14 incorporated or Socata Modification Kit OPT10 908100 incorporated, accomplish the following on the wing front attachments on the fuselage sides: (1) If no cracks are found on the wing front attachments on the fuselage sides during any inspection required by paragraph (a) of this AD, upon accumulating 6,000 landings on these wing front attachments or within the next 100 landings after the effective date of this AD, whichever occurs later, and thereafter at intervals not to exceed 12,000 landings provided no cracks are found during any inspection required by paragraph (a) of this AD, incorporate Modification Kit OPT10 919800 in accordance with Socata Technical Instruction of Modification OPT10 9198-53, dated October 1994. (2) If a crack(s) is found on the wing front attachments on the fuselage sides during any inspection required by paragraph (a) of this AD, prior to further flight, incorporate Modification Kit OPT10 919800 in accordance with Socata Technical Instruction of Modification OPT10 9198-53, dated October 1994. Incorporate this kit at intervals not to exceed 12,000 landings thereafter provided no cracks are found during any inspection required by paragraph (a) of this AD. (d) For Models TB9 and TB10 airplanes, with a serial number in the range of 1 through 399, or with a serial number of 413; that have either Socata Service Letter (SL) 10-14 incorporated or Socata Modification Kit OPT10 908100 incorporated, accomplish the following on the wing front attachments on the fuselage sides: (1) If no cracks are found on the wing front attachments on the fuselage sides during any inspection required by paragraph (a) of this AD, upon accumulating 12,000 landings on these wing front attachments or within the next 100 landings after the effective date of this AD, whichever occurs later, and thereafter at intervals not to exceed 12,000 landings provided no cracks are found during any inspection required by paragraph (a) of this AD, incorporate Modification Kit OPT10 919800 in accordance with Socata Technical Instruction of Modification OPT10 9198-53, dated October 1994. (2) If a crack(s) is found on the wing front attachments on the fuselage sides during any inspection required by paragraph (a) of this AD, prior to further flight, incorporate Modification Kit OPT10 919800 in accordance with Socata Technical Instruction of Modification OPT10 9198-53, dated October 1994. Incorporate this kit at intervals not to exceed12,000 landings thereafter provided no cracks are found during any inspection required by paragraph (a) of this AD. (e) For Models TB9 and TB10 airplanes, with a serial number in the range of 400 through 412, or with a serial number in the range of 414 through 9999; accomplish the following on the wing front attachments on the fuselage sides: (1) If no cracks are found on the wing front attachments on the fuselage sides during any inspection required by paragraph (a) of this AD, upon accumulating 12,000 landings on these wing front attachments or within the next 100 landings after the effective date of this AD, whichever occurs later, and thereafter at intervals not to exceed 12,000 landings provided no cracks are found during any inspection required by paragraph (a) of this AD, incorporate Modification Kit OPT10 908100 in accordance with Socata Technical Instruction of Modification OPT10 9081-53, Amendment 2, dated October 1994. (2) If a crack(s) is found on the wingfront attachments on the fuselage sides during any inspection required by paragraph (a) of this AD, prior to further flight, incorporate Modification Kit OPT10 908100 in accordance with Socata Technical Instruction of Modification OPT10 9081-53, Amendment 2, dated October 1994. Incorporate this kit at intervals not to exceed 12,000 landings thereafter provided no cracks are found during any inspection required by paragraph (a) of this AD. NOTE 3: "Unless already accomplished" credit may be used if the kits that are required by paragraphs (c)(1), (d)(1), and (e)(1) of this AD are already incorporated on the applicable airplanes. As specified in the AD, repetitive incorporation of these kits would still be required at intervals not to exceed 12,000 landings provided no cracks are found. (f) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished. (g) An alternative method of compliance or adjustment of the initial or repetitive compliance times that provides an equivalent level of safety may be approved by the Manager, Small Airplane Directorate, FAA, 1201 Walnut, suite 900, Kansas City, Missouri 64106. The request shall be forwarded through an appropriate FAA Maintenance Inspector, who may add comments and then send it to the Manager, Small Airplane Directorate. NOTE 4: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the Small Airplane Directorate. (h) Questions or technical information related to the service information referenced in this AD should be directed to the SOCATA - Groupe AEROSPATIALE, Socata Product Support, Aeroport Tarbes-Ossun-Lourdes, B P 930, 65009 Tarbes Cedex, France; telephone: 33-5-62-41-76-52; facsimile: 33-5-62-41-76-54; or the Product Support Manager, SOCATA Aircraft, North Perry Airport, 7501 Pembroke Road, Pembroke Pines, Florida 33023; telephone: (954) 893-1400; facsimile: (954) 964-1402. This service information may be examined at the FAA, Central Region, Office of the Regional Counsel, Room 1558, 601 E. 12th Street, Kansas City, Missouri. (i) The inspections required by this AD shall be done in accordance with Socata Service Bulletin No. SB 10-081-57, Amendment 1, dated August 1996. The modifications required by this AD shall be done in accordance with Socata Technical Instruction of Modification OPT10 9198-53, dated October 1994; Socata Technical Instruction of Modification OPT10 9081-53, Amendment 2, dated October 1994; and Socata Technical Instruction No. 9110, which incorporates the following pages: Pages Revision Level Date 0 and 1 Amendment 1 January 31, 1992 2 through 11 Original Issue October 1985 This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from SOCATA - Groupe AEROSPATIALE, Socata Product Support, Aeroport Tarbes-Ossun-Lourdes, B P 930, 65009 Tarbes Cedex, France or the Product Support Manager, SOCATA Aircraft, North Perry Airport, 7501 Pembroke Road, Pembroke Pines, Florida 33023. Copies may be inspected at the FAA, Central Region, Office of the Regional Counsel, Room 1558, 601 E. 12th Street, Kansas City, Missouri, or at the Office of the Federal Register, 800 North Capitol Street, NW, suite 700, Washington, DC. NOTE 5: The subject of this AD is addressed in French AD 94-264(A), dated December 7, 1994. (j) This amendment becomes effective on September 21, 1998.