2026-13-07: Equipment/furnishings

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2026-13-07 The Boeing Company: Amendment 39-23389; Docket No. FAA-2025-3428; Project Identifier AD-2024-00428-T. (a) Effective Date This airworthiness directive (AD) is effective August 6, 2026. (b) Affected ADs None. (c) Applicability This AD applies to The Boeing Company airplanes, certificated in any category, as specified in paragraphs (c)(1) and (2) of this AD. (1) Model 787-8 and 787-9 airplanes as identified in Boeing Special Attention Requirements Bulletin B787-81205-SB250253-00 RB, Issue 002, dated July 11, 2024. (2) Model 787-10 airplanes as identified in Boeing Requirements Bulletin B787-81205-SB250254-00 RB, Issue 001, dated February 22, 2021. (d) Subject Air Transport Association (ATA) of America Code 25, Equipment/furnishings. (e) Unsafe Condition This AD was prompted by reports of door assist handles pulled loose from their lower attach point in the doorway support bracket during pre-flight checks. The FAA is issuing this AD to address loose door assist handles. The unsafe condition, if not addressed, could result in door assist handles becoming detached, which could cause injuries to passengers, crew, or maintenance personnel when opening the door, and could limit exit from the airplane during a time-limited emergency evacuation. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Required Actions (1) For the airplanes identified in paragraph (c)(1) of this AD: Except as specified by paragraph (h) of this AD, at the applicable times specified in the "Compliance" paragraph of Boeing Special Attention Requirements Bulletin B787-81205-SB250253-00 RB, Issue 002, dated July 11, 2024, do all applicable actions identified in, and in accordance with, the Accomplishment Instructions of Boeing Special Attention Requirements Bulletin B787-81205-SB250253-00 RB, Issue 002, dated July 11, 2024. Note 1 to paragraph (g)(1): Guidance for accomplishing the actions required by this AD can be found in Boeing Special Attention Service Bulletin B787-81205-SB250253-00, Issue 002, dated July 11, 2024, which is referred to in Boeing Special Attention Requirements Bulletin B787-81205-SB250253-00 RB, Issue 002, dated July 11, 2024. (2) For the airplanes identified in paragraph (c)(2) of this AD: Except as specified by paragraph (h) of this AD, at the applicable times specified in the "Compliance" paragraph of Boeing Requirements Bulletin B787-81205-SB250254-00 RB, Issue 001, dated February 22, 2021, do all applicable actions identified in, and in accordance with, the Accomplishment Instructions of Boeing Requirements Bulletin B787-81205-SB250254-00 RB, Issue 001, dated February 22, 2021. Note 2 to paragraph (g)(2): Guidance for accomplishing the actions required by this AD can be found in Boeing Service Bulletin B787-81205-SB250254-00, Issue 001, dated February 22, 2021, which is referred to in Boeing Requirements Bulletin B787-81205-SB250254-00 RB, Issue 001, dated February 22, 2021. (h) Exceptions to Requirements Bulletin Specifications (1) Where the Compliance Time columns of the tables in the "Compliance" paragraph of Boeing Special Attention Requirements Bulletin B787-81205-SB250253-00 RB, Issue 002, dated July 11, 2024, refer to the Issue 002 date of Requirements Bulletin B787-81205-SB250253-00 RB, this AD requires using the effective date of this AD. (2) Where the Compliance Time column of the table in the "Compliance" paragraph of Boeing Requirements Bulletin B787-81205-SB250254-00 RB, Issue 001, dated February 22, 2021, refer to the Issue 001 date of Requirements Bulletin B787-81205-SB250254-00 RB, this AD requires using the effective date of this AD. (3) Where Table 1 of "Task 2-Left Side Doorway Assist Handle Support Bracket Retainer-Final Installation [Group 1-3:]" and "Task 3-Right Side Doorway Assist Handle Support Bracket Retainer-Final Installation [Group 1-3]" in the Accomplishment Instructions of Boeing Requirements Bulletin B787-81205-SB250254-00 RB, Issue 001, dated February 22, 2021, specifies to apply adhesive BMS5-105, TYPE 5, this AD allows the application of alternative material, BMS5-105, Type II or Type VI. (4) Where the Safran material specified in Boeing Special Attention Requirements Bulletin B787-81205-SB250253-00 RB, Issue 002, dated July 11, 2024, states to use adhesive Uralane 5774 A/C, this AD allows the use of alternative adhesive, Uralane 5774-1 A/C. (i) Credit for Previous Actions This paragraph provides credit for the actions specified in paragraph (g) of this AD, if those actions were performed before the effective date of this AD using Boeing Requirements Bulletin B787-1205-SB250253-00 RB, Issue 001, dated June 18, 2021. (j) Alternative Methods of Compliance (AMOCs) (1) The Manager, AIR-520, Continued Operational Safety Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the certification office, send it to the attention of the person identified in paragraph (k)(1) of this AD. Information may be emailed to: AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) An AMOC that provides an acceptable level of safety may be used for any repair, modification, or alteration required by this AD if it is approved by The Boeing Company Organization Designation Authorization (ODA) that has been authorized by the Manager, AIR-520, Continued Operational Safety Branch, FAA, to make those findings. To be approved, the repair method, modification deviation, or alteration deviation must meet the certification basis of the airplane, and the approval must specifically refer to this AD. (k) Additional Information (1) For more information about this AD, contact Julie Linn, Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; phone: 206-231-3584; email: julie.linn@faa.gov. (2) Material identified in this AD that is not incorporated by reference is available at the address specified in paragraph (l)(3) this AD. (l) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this material as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) Boeing Requirements Bulletin B787-81205-SB250254-00 RB, Issue 001, dated February 22, 2021. (ii) Boeing Special Attention Requirements Bulletin B787-81205-SB250253-00 RB, Issue 002, dated July 11, 2024. (3) For the Boeing material identified in this AD, contact Boeing Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; telephone 562-797-1717; website myboeingfleet.com. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email fr.inspection@nara.gov. Issued on June 26, 2026. Brian Knaup, Acting Deputy Director, Integrated Certificate Management Division, Aircraft Certification Service. [FR Doc. 2026-13475 Filed 7-1-26; 8:45 am]BILLING CODE 4910-13-P