2025-09-05: Fuselage

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2025-09-05 Airbus SAS: Amendment 39-23026; Docket No. FAA-2024-2548; Project Identifier MCAI-2024-00401-T. (a) Effective Date This airworthiness directive (AD) is effective June 5, 2025. (b) Affected ADs None. (c) Applicability This AD applies to the Airbus SAS airplanes, certificated in any category, as identified in paragraphs (c)(1) through (4) of this AD and in European Union Aviation Safety Agency (EASA) AD 2024-0135, dated July 10, 2024 (EASA AD 2024-0135). (1) Model A318-111, -112, -121, and -122 airplanes. (2) Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes. (3) Model A320-211, -212, -214, -216, -231, -232, and -233 airplanes. (4) Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes. (d) Subject Air Transport Association (ATA) of America Code 53, Fuselage. (e) Unsafe Condition This AD was prompted by cracks being found during full-scale fatigue testing of the keel beam bottom panel between the edge profile and stringer run-out at frame 46 and stringer 37, left- and right-hand sides. The FAA is issuing this AD to address crack propagation in this area. The unsafe condition, if not addressed, could result in reduced structural integrity of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraphs (h) and (i) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2024-0135. (h) Exceptions to EASA AD 2024-0135 (1) Where EASA AD 2024-0135 refers to its effective date, this AD requires using the effective date of this AD. (2) Where paragraph (2) of EASA AD 2024-0135 specifies "if, during any inspection as required by paragraph (1) of this AD, discrepancies are detected, as defined in the SB, before next flight, contact Airbus for approved repair instructions and accomplish those instructions accordingly," this AD requires replacing that text with "if, during any inspection as required by paragraph (1) of this AD, any cracking is detected, the cracking must be repaired before further flight using a method approved by the Manager, AIR-520, Continued Operational Safety Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature." (3) Where paragraph (3) of EASA AD 2024-0135 specifies "unless otherwise stated in the repair instructions provide by Airbus," this AD requires replacing that text with "unless otherwise stated in the repair instructions provided by the Manager, AIR-520, Continued Operational Safety Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature." (4) This AD does not adopt the "Remarks" section of EASA AD 2024-0135. (i) No Reporting Requirement Although the material referenced in EASA AD 2024-0135 specifies to submit certain information to the manufacturer, this AD does not include that requirement. (j) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, AIR-520, Continued Operational Safety Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of AIR-520, Continued Operational Safety Branch, send it to the attention of the person identified in paragraph (k) of this AD and email to: [email protected] . Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, AIR-520, Continued Operational Safety Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (3) Required for Compliance (RC): Except as required by paragraph (j)(2) of this AD, if any material contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (k) Additional Information For more information about this AD, contact Timothy Dowling, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 206-231-3667; email [email protected]. (l) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this material as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2024-0135, dated July 10, 2024. (ii) [Reserved] (3) For EASA material identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email [email protected]. You may find this material on the EASA website at ad.easa.europa.eu. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email [email protected]. Issued on April 24, 2025. Peter A. White, Deputy Director, Integrated Certificate Management Division, Aircraft Certification Service. [FR Doc. 2025-07488 Filed 4-30-25; 8:45 am]BILLING CODE 4910-13-P