2023-22-07: Fuselage

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2023-22-07 Deutsche Aircraft GmbH (Type Certificate Previously Held by 328 Support Services GmbH; AvCraft Aerospace GmbH; Fairchild Dornier GmbH; Dornier Luftfahrt GmbH): Amendment 39-22591; Docket No. FAA-2023-1707; Project Identifier MCAI-2023-00605-T. (a) Effective Date This airworthiness directive (AD) is effective December 26, 2023. (b) Affected ADs None. (c) Applicability This AD applies to all Deutsche Aircraft GmbH (Type Certificate Previously Held by 328 Support Services GmbH; AvCraft Aerospace GmbH; Fairchild Dornier GmbH; Dornier Luftfahrt GmbH) Model 328-100 airplanes, certificated in any category. (d) Subject Air Transport Association (ATA) of America Code: 53, Fuselage. (e) Unsafe Condition This AD was prompted by a report of finding cracks in fuselage frames (FR) 24 and FR26. The FAA is issuing this AD to address cracks in FR24 and FR26. The unsafe condition, if not addressed, could result in failure of load carrying structural elements, possibly resulting in reduced integrity of the fuselage. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2023-0081, dated April 18, 2023 (EASA AD 2023-0081). (h) Exceptions to EASA AD 2023-0081 (1) Where EASA AD 2023-0081 refers to its effective date, this AD requires using the effective date of this AD. (2) Where paragraph (1) of EASA AD 2023-0081 refers to a compliance time of "within 1,500 flight cycles (FC) or during accomplishment of Deutsche Aircraft GmbH Dornier 328 Maintenance Review Board Report (MRBR) task 53-41-37-02, whichever occurs first after the effective date of this AD." for this AD replace those words with "within 1,500 flight cycles after the effective date of this AD." (3) Where paragraph (2) of EASA AD 2023-0081 refers to "damages," for this AD damages are any cracks, including surface cracks. (4) This AD does not adopt the "Remarks" section of EASA AD 2023-0081. (5) Where paragraph (2) of EASA AD 2023-0081 specifies "before next flight, contact Deutsche Aircraft GmbH for approved repair instructions, and within the compliance time indicated therein, accomplish the repair accordingly, including any post-repair maintenance actions" this AD requires replacing those words with "repair cracking before further flight using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Deutsche Aircraft GmbH's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. Any post-repair maintenance actions must be done at the time specified in the approved instructions." (i) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the International Validation Branch, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Deutsche Aircraft GmbH's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (j) Additional Information For more information about this AD, contact Todd Thompson, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 206-231-3228; email todd.thompson@faa.gov. (k) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2023-0081, dated April 18, 2023. (ii) [Reserved] (3) For EASA AD 2023-0081, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email: ADs@easa.europa.eu; website: easa.europa.eu. You may find this EASA AD on the EASA website: ad.easa.europa.eu. (4) You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th Street, Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email fr.inspection@nara.gov. Issued on October 30, 2023. Victor Wicklund, Deputy Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2023-25504 Filed 11-17-23; 8:45 am]BILLING CODE 4910-13-P