2023-14-06: Main Landing Gear Strut, Axle, Truck

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2023-14-06 Airbus Helicopters: Amendment 39-22506; Docket No. FAA-2023-0016; Project Identifier MCAI-2022-00416-R. (a) Effective Date This airworthiness directive (AD) is effective September 8, 2023. (b) Affected ADs None. (c) Applicability This AD applies to all Airbus Helicopters Model EC120B, EC130B4, and EC130T2 helicopters, certificated in any category. (d) Subject Joint Aircraft Service Component (JASC) Code: 3213, Main Landing Gear Strut, Axle, Truck. (e) Unsafe Condition This AD was prompted by a report of corrosion detected on certain part-numbered landing gear assemblies. The FAA is issuing this AD to detect corrosion and cracks on the landing gear tubes. The unsafe condition, if not addressed, could result in the landing gear collapsing, damage to the helicopter, and injury to occupants. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Required Actions (1) Within 13 months after the effective date of this AD, for Model EC120B helicopters with landing gear assembly part number (P/N) C321A2106102, P/N C321A2501101, P/N C321A2501102, P/N C321A2601051AA, P/N C321A2601051CA, or P/N C321A2601052 installed, and for Model EC130B4 and EC130T2 helicopters with landing gear assembly P/N 350A41-0077-0201, P/N 350A41-0080-1102, P/N 350A41-0080-1103, P/N 350A41-0081-0201, P/N 350A41-0082-0101, or P/N 350A41-0082-0102 installed, except those having a date of first installation on a helicopter of February 16, 2022 or later; and for helicopters with a landing gear assembly having a P/N specified in this paragraph, with an unknown installation date, do the following: (i) Remove the landing gear fairing from the rear crossbeam and clean the external areas of each of the landing gear tubes item a, item c, item d, and item e, including Zones B1, B2, C1, C2, D, E, F, and M as depicted in Detail A, Figure 3, and Details B and C, Figure 4 of Airbus Helicopters Alert Service Bulletin (ASB) No. EC120-32A014 (ASB EC120-32A014 Rev 1), or as depicted in Detail A, Figure 4, and Details B and C, Figure 5 of Airbus Helicopters ASB No. EC130-32A013 (ASB EC130-32A013 Rev 1), both Revision 1, and both dated October 17, 2022, as applicable to your model helicopter. (ii) Visually inspect the external areas of each of the landing gear tubes item a, item c, item d, and item e, including Zones B1, B2, C1, C2, D, E, F, and M for corrosion (including, but not limited to leafing and exfoliant corrosion) and cracks. (A) If any crack or leafing or exfoliant corrosion is detected, before further flight, remove the affected part from service and replace it with an airworthy part. (B) If any corrosion is detected in Zone C1, C2, or E, other than leafing or exfoliant corrosion, before further flight, disassemble the landing gear and remove all corrosion from all zones. (C) If any corrosion is detected in only Zone B1, B2, D, F, or M, other than leafing or exfoliant corrosion, before further flight, remove all corrosion from all zones. (iii) Borescope inspect the internal side of each of the landing gear tubes item a, item c, item d, and item e, including Zones B1, B2, C1, C2, D, E, F, and M for corrosion (including, but not limited to leafing and exfoliant corrosion) and cracks. (A) If any crack, leafing corrosion, or exfoliant corrosion is detected, before further flight, remove the affected part from service and replace it with an airworthy part. (B) If any corrosion is detected in Zone C1, C2, or E, other than leafing or exfoliant corrosion, before further flight, disassemble the landing gear and remove all corrosion from all zones. (C) If any corrosion is detected in only Zone B1, B2, D, F, or M, other than leafing or exfoliant corrosion, before further flight, remove all corrosion from all zones. (iv) Before further flight after performing the inspections required by paragraphs (g)(1)(ii) and (iii) of this AD, if any corrosion was detected during any inspection required by paragraphs (g)(1)(ii) and (iii) of this AD other than leafing or exfoliant corrosion, using an ultrasonic thickness gauge, measure the remaining thickness of the landing gear tubes in the zones where any corrosion was removed. Interpret the results of the measurement using the criteria specified in Table 3 of ASB EC120-32A014 Rev 1 or Table 3 of ASB EC130-32A013 Rev 1, as applicable to your model helicopter. If the remaining thickness does not meet the permitted criteria as specified, before further flight, remove each affected sub-assembly from service and replace it with an airworthy part. If the remaining thickness meets the permitted criteria as specified, before further flight, accomplish the actions required by paragraph (g)(1)(v) of this AD. (v) Apply a chemical conversion coating (Alodine 1200) or equivalent, and a double layer of chromate Primer P05 and Primer P20, or equivalent, below the collar in Zones F and M and to any reworked zone. (2) For Model EC120B helicopters, as of the effective date of this AD, do not install landing gear assembly P/N C321A2106102, P/N C321A2501101, P/N C321A2501102, P/N C321A2601051AA, P/N C321A2601051CA, or P/N C321A2601052, previously installed with an unknown installation date or a date of first installation on a helicopter before February 16, 2022; and do not install a front crossbeam, rear crossbeam, left-hand (LH) skid assembly, or right-hand (RH) skid assembly having a P/N identified in Table 2 of ASB EC120-32A014 Rev 1, previously installed with an unknown installation date, or a date of first installation on a helicopter before February 16, 2022, on any helicopter; unless the actions required by paragraphs (g)(1)(i) through (v) of this AD, as applicable, have been accomplished on the part. (3) For Model EC130B4 and EC130T2 helicopters, as of the effective date of this AD, do not install landing gear assembly P/N 350A41-0077-0201, P/N 350A41-0080-1102, P/N 350A41-0080-1103, P/N 350A41-0081-0201, P/N 350A41-0082-0101, or P/N 350A41-0082-0102, previously installed with an unknown installation date or a date of first installation on a helicopter before February 16, 2022, and do not install a front crossbeam, rear crossbeam, LH skid assembly, or RH skid assembly, having a P/N identified in Table 2 of ASB EC130-32A013 Rev 1, previously installed with an unknown installation date, or a date of first installation on a helicopter before February 16, 2022, on any helicopter, unless the actions required by paragraphs (g)(1)(i) through (v) of this AD, as applicable, have been accomplished on the part. (h) Alternative Methods of Compliance (AMOCs) (1) The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the International Validation Branch, send it to the attention of the person identified in paragraph (i)(2) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (i) Additional Information (1) Refer to European Union Aviation Safety Agency (EASA) AD 2022-0053, dated March 23, 2022, for related information. This EASA AD may be found in the AD docket at regulations.gov under Docket No. FAA-2023-0016. (2) For more information about this AD, contact Stephanie Sunderbruch, Aviation Safety Engineer, FAA, 1600 Stewart Ave., Suite 410, Westbury, NY 11590; telephone (817) 222-4659; email: Stephanie.L.Sunderbruch@faa.gov. (j) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) Airbus Helicopters Alert Service Bulletin (ASB) No. EC120-32A014, Revision 1, dated October 17, 2022. (ii) Airbus Helicopters ASB No. EC130-32A013, Revision 1, dated October 17, 2022. (3) For service information identified in this AD, contact Airbus Helicopters, 2701 North Forum Drive, Grand Prairie, TX 75052; telephone (972) 641-0000 or (800) 232-0323; fax (972) 641-3775; or at airbus.com/en/products-services/helicopters/hcare-services/airbusworld. (4) You may view this service information at the FAA, Office of the Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 6N-321, Fort Worth, TX 76177. For information on the availability of this material at the FAA, call (817) 222-5110. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email: fr.inspection@nara.gov, or go to: www.archives.gov/federal-register/cfr/ibr-locations.html. Issued on July 12, 2023. Victor Wicklund, Deputy Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2023-16555 Filed 8-3-23; 8:45 am]BILLING CODE 4910-13-P