1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2023-03-04 The Boeing Company: Amendment 39-22329; Docket No. FAA-2022-0810; Project Identifier AD-2021-01238-T. (a) Effective Date This airworthiness directive (AD) is effective April 4, 2023. (b) Affected ADs (1) This AD affects AD 2017-11-14, Amendment 39-18913 (82 FR 25954, June 6, 2017) (AD 2017-11-14). (2) This AD also affects AD 2021-24-12, Amendment 39-21833 (86 FR 73660, December 28, 2021) (AD 2021-24-12). (c) Applicability This AD applies to all The Boeing Company Model 777-200, -200LR, -300, -300ER, and 777F series airplanes, certificated in any category. (d) Subject Air Transport Association (ATA) of America Code 57, Wings. (e) Unsafe Condition This AD was prompted by fuel system reviews conducted by the manufacturer. The FAA is issuing this AD to prevent arcing inside the main and center fuel tanks in the event of a fault current or lightning strike, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Required Actions for Certain Airplanes For airplanes identified in Boeing Alert Service Bulletin 777-57A0050, Revision 6, dated August 18, 2021: Except as specified in paragraph (h) of this AD, at the applicable times specified in paragraph 1.E., "Compliance," of Boeing Alert Service Bulletin 777-57A0050, Revision 6, dated August 18, 2021, do all applicable actions ( i.e., installation of Teflon sleeves, cap sealing of fasteners, detailed inspections, and corrective actions) identified in, and in accordance with, the Accomplishment Instructions of Boeing Alert Service Bulletin 777-57A0050, Revision 6, dated August 18, 2021. (h) Exceptions to Service Information Specifications (1) Where Boeing Alert Service Bulletin 777-57A0050, Revision 6, dated August 18, 2021, uses the phrase "the revision 5 date of this service bulletin" or "the revision 6 date of this service bulletin," this AD requires using "the effective date of this AD." (2) Where circle symbol 1 of sheet 2 of Figures 172, 173, and 174 of Boeing Alert Service Bulletin 777-57A0050, Revision 6, dated August 18, 2021, points to the outboard side of rib no. 9 for the locate and cap seal task or the inspection task, as applicable, in step 1 of sheet 3, for this AD, circle symbol 1 points to the seven fasteners located at the inboard side of rib no. 9 (adjacent to the right side of the identified seven fasteners). (3) Where circle symbol 1, next to the text "7 locations," of sheet 2 of Figure 175 and Figure 176 of Boeing Alert Service Bulletin 777-57A0050, Revision 6, dated August 18, 2021, points to the outboard side of rib no. 9 for the locate and cap seal task or the inspection task, as applicable, in step 1 of sheet 3, for this AD, circle symbol 1, next to the text "7 locations," points to the seven fasteners located at the inboard side of rib no. 9 (adjacent to the right side of the identified seven fasteners). (4) Where circle symbol 1, next to the text "7 locations," of sheet 4 of Figure 179 and Figure 180 of Boeing Alert Service Bulletin 777-57A0050, Revision 6, dated August 18, 2021, points to the outboard side of rib no. 9 for the locate and cap seal task or the inspection task, as applicable, in step 1 of sheet 6, for this AD, circle symbol 1, next to the text "7 locations," points to the seven fasteners located at the inboard side of rib no. 9 (adjacent to the left side of the identified seven fasteners). (5) Where Boeing Alert Service Bulletin 777-57A0050, Revision 6, dated August 18, 2021, specifies Work Package 28 is applicable to Group 1 through 4, and Group 8, this AD does not require accomplishment of Work Package 28 for Group 1 through 4 only. (6) For Group 1 through 4 airplanes identified in Boeing Alert Service Bulletin 777-57A0050, Revision 6, dated August 18, 2021, on which the actions specified in Work Package 37 of Boeing Alert Service Bulletin 777-57A0050, Revision 6, dated August 18, 2021, have been accomplished, the actions specified in Work Package 38 are not required. (7) Where the Accomplishment Instructions of Boeing Alert Service Bulletin 777-57A0050, Revision 6, dated August 18, 2021, specifies to purge specific fuel tanks (right, left, or center), operators must purge the applicable fuel tank for which access inside the fuel tank is needed to apply cap sealing to the affected fasteners. (i) Maintenance or Inspection Program Revision Within 60 days after the effective date of this AD, revise the existing maintenance or inspection program, as applicable, to incorporate the information for 28-AWL-31 and 28-AWL-32 specified in Section D, "Airworthiness Limitations-Systems," including Subsections D.1, of Section 9, Airworthiness Limitations (AWLs) and Certification Maintenance Requirements (CMRs), D622W001-9, dated August 2022, of Boeing 777-200/200LR/300/300ER/777F Maintenance Planning Data (MPD) Document. The initial compliance time for doing airworthiness limitation instructions (ALI) task 28-AWL-32 is at the applicable time specified in paragraph (i)(1) or (2) of this AD: (1) For airplanes having line number (L/Ns) 1 through 503 inclusive: Within 3,750 days after accomplishment of the actions specified in Boeing Service Bulletin 777-57A0050; within 60 months after the effective date of this AD; or within 3,750 days after the most recent inspection was performed as specified in AWL No. 28-AWL-32; whichever is latest. (2) For airplanes having L/Ns 504 and subsequent: Within 3,750 days after the date of issuance of the original airworthiness certificate or the date of issuance of the original export certificate of airworthiness; within 60 months after the effective date of this AD; or within 3,750 days after the most recent inspection was performed as specified in AWL No. 28-AWL-32; whichever is latest. (j) Credit for Previous Actions This paragraph provides credit for the maintenance or inspection program revision specified in paragraph (i) of this AD, if the revision was performed before the effective date of this AD using Section 9, Airworthiness Limitations (AWLs) and Certification Maintenance Requirements (CMRs), D622W001-9, dated March 2022, dated June 2022, or dated July 2022, of Boeing 777 200/200LR/300/300ER/777F Maintenance Planning Data (MPD) Document; provided that the corrections specified in paragraphs (j)(1) through (4) of this AD were also incorporated. The following exceptions apply to 28-AWL-31 and 28-AWL-32 of Section D, "Airworthiness Limitations-Systems," including Subsections D.1 of Section 9, Airworthiness Limitations (AWLs) and Certification Maintenance Requirements (CMRs), D622W001-9, of Boeing 777-200/200LR/300/300ER/777F Maintenance Planning Data (MPD) Document. (1) In paragraph 1.i., change "Front Spar Bulkhead (Center Tank)" to "Front Spar Bulkhead (Center Wing Tank Fuel Quantity Greater than 12,400 Gallons)." (2) In paragraph 1.i.II, change "For 777-200, 777-200LR, 777-300, and 777-300ER airplanes, L/N 562 and on" to "L/N 562 and on, except 777F." (3) In paragraph 1.i.III., change "For 777F airplanes, L/N 718 and on" to "For 777F airplanes." (4) In paragraph 1.j., change "Rear Spar Bulkhead (Center Tank)" to "Rear Spar Bulkhead (Center Wing Tank Fuel Quantity Greater than 12,400 Gallons)." (k) No Alternative Actions, Intervals, or Critical Design Configuration Control Limitations (CDCCLs) After the existing maintenance or inspection program has been revised as required by paragraph (i) of this AD, no alternative actions ( e.g., inspections), intervals, or CDCCLs may be used unless the actions, intervals, and CDCCLs are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (m) of this AD. (l) Terminating Action for Certain Requirements of AD 2017-11-14 and AD 2021-24-12 (1) Accomplishment of the actions required by paragraph (g) of this AD terminates the requirements of paragraphs (g)(1), (i), and (j) of AD 2017-11-14. (2) Accomplishment of the revision required by paragraph (i) of this AD terminates the requirements of paragraphs (g)(6) and (h) of AD 2021-24-12. (m) Alternative Methods of Compliance (AMOCs) (1) The Manager, Seattle ACO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the certification office, send it to the attention of the person identified in paragraph (n) of this AD. Information may be emailed to:
[email protected]. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (3) An AMOC that provides an acceptable level of safety may be used for any repair, modification, or alteration required by this AD if it is approved by The Boeing Company Organization Designation Authorization (ODA) that has been authorized by the Manager, Seattle ACO Branch, FAA, to make those findings. To be approved, the repair method, modification deviation, or alteration deviation must meet the certification basis of the airplane, and the approval must specifically refer to this AD. (n) Related Information For more information about this AD, contact Kevin Nguyen, Aerospace Engineer, Propulsion Section, FAA, Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206-231-3555; email:
[email protected]. (o) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) Boeing Alert Service Bulletin 777-57A0050, Revision 6, dated August 18, 2021. (ii) Section 9, Airworthiness Limitations (AWLs) and Certification Maintenance Requirements (CMRs), D622W001-9, dated August 2022, of Boeing 777 200/200LR/300/300ER/777F Maintenance Planning Data (MPD) Document. (3) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; telephone 562-797-1717; website myboeingfleet.com . (4) You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA,
[email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html. Issued on February 2, 2023. Christina Underwood, Acting Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2023-04024 Filed 2-27-23; 8:45 am]BILLING CODE 4910-13-P