2022-27-01: Wings

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2022-27-01 Airbus SAS: Amendment 39-22286; Docket No. FAA-2022-1248; Project Identifier MCAI-2022-00609-T. (a) Effective Date This airworthiness directive (AD) is effective February 2, 2023. (b) Affected ADs None. (c) Applicability This AD applies to Airbus SAS Model A350-941 and -1041 airplanes, certificated in any category, as identified in European Union Aviation Safety Agency (EASA) AD 2022-0080, dated May 9, 2022 (EASA AD 2022-0080). (d) Subject Air Transport Association (ATA) of America Code 57, Wings. (e) Unsafe Condition This AD was prompted by a report that during flight and fatigue testing it was detected that some fasteners installed in the center wing box (CWB) rotated inside their fastener holes. The FAA is issuing this AD to address fasteners installed in the CWB rotating inside their fastener holes, which if not corrected, could lead to loss of a fastener clamping and cracking of the nut sealant cover, possibly resulting, in case of lightning strike, in a fuel tank explosion and consequent loss of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2022-0080. (h) Exceptions to EASA AD 2022-0080 (1) Where EASA AD 2022-0080 refers to its effective date, this AD requires using the effective date of this AD. (2) The "Remarks" section of EASA AD 2022-0080 does not apply to this AD. (i) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the International Validation Branch, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (j) Additional Information For more information about this AD, contact Dat Le, Aerospace Engineer, Large Aircraft Section, FAA, International Validation Branch, 2200 South 216th St., Des Moines, WA 98198; telephone 516-228-7317; email [email protected]. (k) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2022-0080, dated May 9, 2022. (ii) [Reserved] (3) For EASA AD 2022-0080, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email [email protected]; website easa.europa.eu. You may find this EASA AD on the EASA website at ad.easa.europa.eu. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email [email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html. Issued on December 20, 2022. Christina Underwood, Acting Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2022-28271 Filed 12-28-22; 8:45 am]BILLING CODE 4910-13-P