1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2022-17-04 De Havilland Aircraft of Canada Limited (Type Certificate Previously Held by Bombardier, Inc.): Amendment 39-22142; Docket No. FAA-2022-0287; Project Identifier MCAI-2020-01602-T. (a) Effective Date This airworthiness directive (AD) is effective November 1, 2022. (b) Affected ADs None. (c) Applicability This AD applies to De Havilland Aircraft of Canada Limited (type certificate previously held by Bombardier, Inc.) Model DHC-8-400, -401, and -402 airplanes, certificated in any category, serial numbers (S/Ns) 4001, 4003, and subsequent. (d) Subject Air Transport Association (ATA) of America Code 28, Fuel System; and 05, Time Limits/Maintenance Checks. (e) Unsafe Condition This AD was prompted by reports of broken P-clamps on the pressure relief line and the motive flow line in the fuel tanks, and a subsequent determination that certain service information lacked instructions for maintaining appropriate clearance between certain fuel tubes and their support brackets, and may also have led to incorrect installation of certain Teflon TM sleeves. The FAA is issuing this AD to address adverse impacts on the integrity of the electrical bonding paths throughout the fuel line, which could lead to arcing between the vent line and airplane structure, and could result in possible fuel tank ignition in the event of a lightning strike. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Definition For the purposes of this AD, "prohibited tasks" are defined as any task identified in paragraph (l) of this AD and any procedure or task that specifies fuel tank access using non-manufacturer-approved procedures. (h) Modifications (1) For airplanes having S/N 4001 and 4003 through 4525 inclusive: Within 6,000 flight hours or 36 months after the effective date of this AD, whichever occurs first, increase the hole size in the collector tank partition wall, inspect the motive flow line for damage, and replace the associated grommet and motive flow line, in accordance with paragraph 3.B. of the Accomplishment Instructions of Bombardier Service Bulletin 84-28-18, Revision B, dated April 20, 2017. (2) For airplanes having S/N 4001 and 4003 through 4533 inclusive, on which Bombardier Service Bulletin 84-28-19, dated August 16, 2016; or Revision A, dated November 4, 2016; has not been done: Within 6,000 flight hours or 36 months after the effective date of this AD, whichever occurs first, replace the affected single nut plate brackets and standoffs at the affected left-hand (LH) and right-hand (RH) wing stations on the motive flow line and pressure relief line, in accordance with paragraphs 3.B. and 3.C. of Bombardier Service Bulletin 84-28-19, Revision D, dated February 16, 2018. (3) Accomplishing Bombardier Repair Drawing 8/4-28-018, Issue 1, dated October 30, 2017; Issue 2, dated June 12, 2018; Issue 3, dated June 21, 2018; or Issue 4, dated July 27, 2018; is a method of compliance (MOC) only for the replacement of the affected single nut plate brackets and standoffs on the motive flow line and vent line at LH and RH wing stations Yw ± 209.019 and Yw ± 317.019 required by paragraph (h)(2) of this AD. (4) Accomplishing Bombardier Repair Drawing 8/4-28-018, Issue 1, dated October 30, 2017; Issue 2, dated June 12, 2018; Issue 3, dated June 21, 2018; or Issue 4, dated July 27, 2018; prior to the effective date of this AD, along with the replacement of the affected single nut plate brackets and standoffs on the motive flow line, vent line, pressure relief line, and scavenge line at LH and RH wing stations Yw ± 209.019, Yw ± 317.019, and Yw ± 371.019, is acceptable for compliance for the actions required by paragraph (h)(2) of this AD. (5) For airplanes having S/N 4001 and 4003 through 4533 inclusive, on which Bombardier Service Bulletin 84-28-19, dated August 16, 2016; or Revision A, dated November 4, 2016; has been done: Within 6,000 flight hours or 36 months after the effective date of this AD, whichever occurs first, inspect the motive flow line and vent line at wing stations -371.019 and 371.019 in the LH and RH fuel tanks, respectively, to ensure that these fuel tubes are adequately supported, and inspect the fuel tubes to verify that an appropriate clearance has been maintained between the fuel tubes and their support brackets, in accordance with paragraph 3.B., step (13), and paragraph 3.C., of Bombardier Service Bulletin 84-28-19, Revision D, dated February 16, 2018. (6) For airplanes having S/N 4001 and 4003 through 4572 inclusive: Within 8,000 flight hours or 48 months after the effective date of this AD, whichever occurs first, install Teflon TM sleeves on the vent line at wing stations Yw ± 209.019 and Yw ± 371.019 in the LH and RH fuel tanks, inspect the Teflon TM sleeve installation on the vent line at wing stations Yw ± 317.019 in the LH and RH fuel tanks, and if any sleeve is incorrectly installed, reposition the Teflon TM sleeves before further flight, in accordance with paragraphs 3.B. and 3.C. of the Accomplishment Instructions of Bombardier Service Bulletin 84-28-24, dated November 27, 2017. (7) Prior to accomplishment of the actions required by paragraph (h)(6) of this AD, the applicable actions specified in paragraph (h)(2) or (5) of this AD must be done. For airplanes on which Bombardier Modification Summary (ModSum) 4Q113904 has been accomplished prior to accomplishment of the actions required by paragraph (h)(6) of this AD, no further action is required by this paragraph. (8) For airplanes having S/N 4001 and 4003 through 4575 inclusive: Within 8,000 flight hours or 48 months after the effective date of this AD, whichever occurs first, inspect the Teflon TM sleeve installation on the vent line in the LH and RH fuel tanks for correct installation and damage, and if the sleeves are incorrectly installed or damage is found, before further flight, replace and reposition the Teflon TM sleeves, as applicable, in accordance with paragraphs 3.B. and 3.C. of the Accomplishment Instructions of Bombardier Service Bulletin 84-28-25, dated November 27, 2017. (9) Prior to accomplishment of the actions required by paragraph (h)(8) of this AD, the applicable actions specified in paragraph (h)(2) or (5) of this AD must be done. For airplanes on which Bombardier ModSum 4Q113904 has been accomplished prior to accomplishment of the actions required by paragraph (h)(8) of this AD, no further action is required by this paragraph. (i) Verification and Rework for Existing Maintenance Program (1) For airplanes having S/N 4001 and 4003 through 4575 inclusive, on which the actions required by paragraph (h)(6) or (8) of this AD have been done before the effective date of this AD, or that have complied with paragraph (m)(4) of this AD: Within 60 days after the effective date of this AD, review the airplane maintenance records to confirm if any of the prohibited tasks (defined in paragraph (g) of this AD) were accomplished during or after compliance with paragraph (h)(6) or (8) of this AD or paragraph (m)(4) of this AD. (i) If any of the prohibited tasks were accomplished during or after compliance with paragraph (h)(6) or (m)(4) of this AD, or if it cannot be conclusively confirmed that they were not accomplished during or after compliance with paragraph (h)(6) or paragraph (m)(4) of this AD: Within 8,000 flight hours or 48 months after the effective date of this AD, whichever occurs first, do the actions required by paragraph (h)(6) of this AD and, as applicable, comply with the requirements of paragraph (h)(7) of this AD. (ii) If any of the prohibited tasks were accomplished during or after compliance with paragraph (h)(8) of this AD, or if it cannot be conclusively confirmed that they were not accomplished during or after compliance with paragraph (h)(8) of this AD: Within 8,000 flight hours or 48 months after the effective date of this AD, whichever occurs first, do the actions required by paragraph (h)(8) of this AD and, as applicable, comply with the requirements of paragraph (h)(9) of this AD. (2) For airplanes having S/N 4573 and subsequent, with an airplane date of manufacture, as identified on the identification plate of the airplane, dated before the effective date of this AD: Within 60 days after the effective date of this AD, review the airplane maintenance records to confirm if any of the prohibited tasks (defined in paragraph (g) of this AD) were accomplished on or after the airplane date of manufacture. If any of the prohibited tasks were accomplished on or after the airplane date of manufacture, or if it cannot be conclusively confirmed that they were not accomplished on or after the airplane date of manufacture, within 8,000 flight hours or 48 months after the effective date of this AD, whichever occurs first, obtain and follow instructions for rework using a method approved by the Manager, New York ACO Branch, FAA; or Transport Canada Civil Aviation (TCCA); or De Havilland Aircraft of Canada Limited's TCCA Design Approval Organization (DAO). If approved by the DAO, the approval must include the DAO-authorized signature. (j) Maintenance or Inspection Program Revision For all airplanes: Within 30 days after the effective date of this AD, revise the existing maintenance or inspection program, as applicable, to incorporate the information specified in (Bombardier) Q400 Dash 8 Maintenance Requirements Manual (MRM) Temporary Revision (TR) ALI-0192 and TR ALI-0193, both dated April 24, 2018. The initial compliance time for doing the tasks in (Bombardier) Q400 Dash 8 MRM TR ALI-0192, dated April 24, 2018, is at the applicable time specified in paragraph (j)(1) or (2) of this AD, whichever occurs later: (1) Prior to the accumulation of 18,000 total flight cycles or within 108 months since issuance of the original airworthiness certificate or original export certificate of airworthiness, whichever occurs first. (2) Within 90 days after the effective date of this AD. (k) No Alternative Actions, Intervals, or Critical Design Configuration Control Limitations (CDCCLs) After the existing maintenance or inspection program has been revised as required by paragraph (j) of this AD, no alternative actions ( e.g., inspections), intervals, or CDCCLs may be used unless the actions, intervals, and CDCCLs are approved as an AMOC in accordance with the procedures specified in paragraph (n)(1) of this AD. (l) Maintenance Task Prohibitions For all airplanes: As of the effective date of this AD, comply with the prohibitions specified in paragraphs (l)(1) and (2) of this AD. (1) It is prohibited to use the Bombardier airplane maintenance manual (AMM) tasks identified in paragraphs (l)(1)(i) through (v) of this AD, which are specified in the Bombardier Q400 Dash 8 AMM, PSM 1-84-2, Revision 59 dated October 5, 2017, or earlier revisions of these tasks. TRs including these AMM tasks, dated November 27, 2017, or earlier, are also prohibited for use except as specified in paragraph (l)(1)(i) through (v) of this AD. (i) Task 28-10-00-280-806, Detailed Inspection of the Teflon TM Sleeve on the Fuel Tank Vent Line, LH and RH (FSL#284000-406), with the exception of (Bombardier) Q400 Dash 8 AMM TR 28-145, dated November 21, 2017. (ii) Task 28-12-06-000-801, Removal of the Outboard Vent Line, with the exception of (Bombardier) Q400 Dash 8 AMM TR 28-146, dated November 21, 2017. (iii) Task 28-12-06-400-801, Installation of the Outboard Vent Line, with the exception of (Bombardier) Q400 Dash 8 AMM TR 28-147, dated November 21, 2017. (iv) Task 28-12-01-000-801, Removal of the Inboard Vent Line, with the exception of (Bombardier) Q400 Dash 8 AMM TR 28-148, dated November 24, 2017. (v) Task 28-12-01-400-801, Installation of the Inboard Vent Line, with the exception of (Bombardier) Q400 Dash 8 AMM TR 28-149, dated November 27, 2017. (2) It is prohibited to use the Bombardier Q400 Dash 8 Maintenance Task Card Manual (MTCM) task cards identified in paragraphs (l)(2)(i) and (ii) of this AD that are specified in the Bombardier Q400 Dash 8 MTCM, PSM 1-84-7TC, Revision 42, dated November 5, 2017, or earlier revisions or amendments of these task cards. MTCM task card revisions or amendments dated November 21, 2017, or earlier, are also prohibited for use, except as specified in paragraphs (l)(2)(i) and (ii) of this AD. (i) Bombardier Q400 Dash 8 MTCM, Maintenance Task Card 000-28-520-704 (Config A01), Revision 42, Amendment 0002, dated November 21, 2017. (ii) Bombardier Q400 Dash 8 MTCM, Maintenance Task Card 000-28-620-704 (Config A01), Revision 42, Amendment 0002, dated November 21, 2017. (m) Credit for Previous Actions (1) This paragraph provides credit for actions required by paragraph (h)(1) of this AD, if those actions were performed before the effective date of this AD using Bombardier Service Bulletin 84-28-18, dated April 20, 2016; or Revision A, dated November 14, 2016. (2) This paragraph provides credit for actions required by paragraph (h)(2) of this AD, if those actions were performed before the effective date of this AD using Bombardier Service Bulletin 84-28-19, Revision B, dated July 28, 2017; or Revision C, dated September 1, 2017. (3) This paragraph provides credit for actions required by paragraph (h)(5) of this AD, if those actions were performed before the effective date of this AD using paragraphs 3.A. and 3.C and paragraph 3.B., step (13) of Bombardier Service Bulletin 84-28-19, Revision B, dated July 28, 2017; or Revision C, dated September 1, 2017. (4) This paragraph provides credit for actions required by paragraph (h)(6) of this AD, if, before the effective date of this AD, the modsums identified in paragraph (m)(4)(i), (ii), or (iii) of this AD were incorporated, and provided the conditions identified in figure 1 to paragraph (m)(4) of this AD have been met. ER27SE22.019 (i) Incorporation of both a modsum identified in paragraph (m)(4)(i)(A) of this AD and a modsum identified in paragraph (m)(4)(i)(B) of this AD. (A) One of the modsums identified in paragraphs (m)(4)(i)(A)( 1 ) through ( 9 ) of this AD. ( 1 ) Bombardier ModSum IS4Q2800023, Revision A, dated February 7, 2017. ( 2 ) Bombardier ModSum IS4Q2800023, Revision B, dated April 11, 2017. ( 3 ) Bombardier ModSum IS4Q2800023, Revision C, dated August 30, 2017. ( 4 ) Bombardier ModSum IS4Q2800023, Revision D, dated October 11, 2017. ( 5 ) Bombardier ModSum IS4Q2800023, Revision E, dated October 19, 2017. ( 6 ) Bombardier ModSum IS4Q2800023, Revision F, dated October 20, 2017. ( 7 ) Bombardier ModSum IS4Q2800023, Revision G, dated November 24, 2017. ( 8 ) Bombardier ModSum IS4Q2800023, Revision H, dated November 29, 2017. ( 9 ) Bombardier ModSum IS4Q2800023, Revision J, dated December 12, 2017. (B) One of the modsums identified in paragraphs (m)(4)(i)(B)( 1 ) through ( 5 ) of this AD. ( 1 ) Bombardier ModSum IS4Q2800025, Revision A, dated October 20, 2017. ( 2 ) Bombardier ModSum IS4Q2800025, Revision B, dated November 3, 2017. ( 3 ) Bombardier ModSum IS4Q2800025, Revision C, dated November 21, 2017. ( 4 ) Bombardier ModSum IS4Q2800025, Revision D, dated November 23, 2017. ( 5 ) Bombardier ModSum IS4Q2800025, Revision E, dated November 29, 2017. (ii) Incorporation of both a modsum identified in paragraph (m)(4)(ii)(A) of this AD and a modsum identified in paragraph (m)(4)(ii)(B) of this AD. (A) Bombardier ModSum IS4Q2800030, Revision A, dated November 3, 2017; or Bombardier ModSum IS4Q2800030, Revision B, dated November 21, 2017. (B) One of the modsums identified in paragraphs (m)(4)(ii)(B)( 1 ) through ( 5 ) of this AD. ( 1 ) Bombardier ModSum IS4Q2800025, Revision A, dated October 20, 2017. ( 2 ) Bombardier ModSum IS4Q2800025, Revision B, dated November 3, 2017. ( 3 ) Bombardier ModSum IS4Q2800025, Revision C, dated November 21, 2017. ( 4 ) Bombardier ModSum IS4Q2800025, Revision D, dated November 23, 2017, ( 5 ) Bombardier ModSum IS4Q2800025, Revision E, dated November 29, 2017. (iii) Incorporation of a modsum identified in paragraphs (m)(4)(iii)(A) through (C) of this AD. (A) Bombardier ModSum IS4Q2800027, Revision A, dated October 27, 2017. (B) Bombardier ModSum IS4Q2800027, Revision B, dated November 9, 2017. (C) Bombardier ModSum IS4Q2800027, Revision C, dated November 15, 2017. (n) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, New York ACO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the certification office, send it to ATTN: Program Manager, Continuing Operational Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, New York ACO Branch, FAA; or TCCA; or De Havilland Aircraft of Canada Limited's TCCA Design Approval Organization (DAO). If approved by the DAO, the approval must include the DAO-authorized signature. (o) Related Information (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) TCCA AD CF-2017-05R2, dated September 20, 2019, for related information. This MCAI may be found in the AD docket at www.regulations.gov by searching for and locating Docket No. FAA-2022-0287. (2) For more information about this AD, contact Joseph Catanzaro, Aerospace Engineer, Airframe and Propulsion Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7366; email
[email protected]. (3) Service information identified in this AD that is not incorporated by reference is available at the addresses specified in paragraphs (p)(3) and (4) of this AD. (p) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) Bombardier Repair Drawing 8/4-28-018, Issue 1, dated October 30, 2017. (ii) Bombardier Repair Drawing 8/4-28-018, Issue 2, dated June 12, 2018. (iii) Bombardier Repair Drawing 8/4-28-018, Issue 3, dated June 21, 2018. (iv) Bombardier Repair Drawing 8/4-28-018, Issue 4, dated July 27, 2018. (v) Bombardier Service Bulletin 84-28-18, Revision B, dated April 20, 2017. (vi) Bombardier Service Bulletin 84-28-19, Revision D, dated February 16, 2018. (vii) Bombardier Service Bulletin 84-28-24, dated November 27, 2017. (viii) Bombardier Service Bulletin 84-28-25, dated November 27, 2017. (ix) Q400 Dash 8 Airplane Maintenance Manual (AMM) TR 28-145, dated November 21, 2017. Note 1 to paragraph (p)(2)(ix): The documents identified in paragraphs (p)(2)(ix) through (xvii) of this AD do not specify a publisher name; these documents were published by Bombardier. (x) Q400 Dash 8 AMM TR 28-146, dated November 21, 2017. (xi) Q400 Dash 8 AMM TR 28-147, dated November 21, 2017. (xii) Q400 Dash 8 AMM TR 28-148, dated November 24, 2017. (xiii) Q400 Dash 8 AMM TR 28-149, dated November 27, 2017. (xiv) Q400 Dash 8 Maintenance Task Card Manual (MTCM), Maintenance Task Card 000-28-520-704 (Config A01), Revision 42, Amendment 0002, dated November 21, 2017. (xv) Q400 Dash 8 MTCM, Maintenance Task Card 000-28-620-704 (Config A01), Revision 42, Amendment 0002, dated November 21, 2017. (xvi) Q400 Dash 8 Maintenance Requirements Manual (MRM) TR ALI-0192, dated April 24, 2018. (xvii) Q400 Dash 8 MRM TR ALI-0193, dated April 24, 2018. (3) For service information identified in this AD, contact De Havilland Aircraft of Canada Limited, Dash 8 Series Customer Response Centre, 5800 Explorer Drive, Mississauga, Ontario, L4W 5K9, Canada; telephone 855-310-1013 or 647-277-5820; email
[email protected]; internet dehavilland.com . (4) You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email
[email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html. Issued on August 4, 2022. Christina Underwood, Acting Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2022-20805 Filed 9-26-22; 8:45 am]BILLING CODE 4910-13-P