1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2022-16-09 The Boeing Company: Amendment 39-22138; Docket No. FAA-2021-1168; Project Identifier AD-2021-00825-T. (a) Effective Date This airworthiness directive (AD) is effective October 20, 2022. (b) Affected ADs None. (c) Applicability This AD applies to The Boeing Company Model 737-8 airplanes, certificated in any category, as identified in Boeing Special Attention Requirements Bulletin 737-57-1352 RB, dated February 1, 2021. (d) Subject Air Transport Association (ATA) of America Code 57, Wings. (e) Unsafe Condition This AD was prompted by a report that, during production, a small number of fasteners in certain locations of the center fuel tank were cap sealed on top of a black stripe of ink with a clear overcoat. This clear overcoat is not an approved surface for sealing and can potentially compromise sealant adhesion. Compromised sealant adhesion can, over time, affect the lightning protection properties of the airplane. The FAA is issuing this AD to address compromised sealant adhesion within the center fuel tank, which, if combined with a flammable center tank ullage and an independent failure of the primary lightning protection feature, could result in ignition of fuel vapors and subsequent explosion of the fuel tank in the event of a lightning strike to that fastener. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Required Actions Within 10 years after the date of issuance of the original airworthiness certificate or the original export certificate of airworthiness, do all applicable actions identified in, and in accordance with, the Accomplishment Instructions of Boeing Special Attention Requirements Bulletin 737-57-1352 RB, dated February 1, 2021, except as specified by paragraph (h) of this AD. Note 1 to paragraph (g): Guidance for accomplishing the actions required by this AD can be found in Boeing Special Attention Service Bulletin 737-57-1352, dated February 1, 2021, which is referred to in Boeing Special Attention Requirements Bulletin 737-57-1352 RB, dated February 1, 2021. (h) Optional Method To Remove Previously Applied Sealant and Black Stripe of Ink, and Reapply Fastener Seal As an option to the sealant application required by paragraph (g) of this AD, it is acceptable to remove the existing sealant and the black stripe of ink prior to reapplying a fastener seal. Remove existing sealant and black stripe of ink as follows: (1) Remove existing sealant to expose the black stripe of ink. (2) Remove existing black stripe of ink using aluminum oxide cloth or paper, 150 to 220 grit. Note 2 to paragraph (h)(2): Take caution not to abrade through the existing oven cured BMS10-20 coating under the black stripe of ink. The BMS10-20 was previously applied during production. (3) Touch up exposed aluminum with Alodine 600 (Type I, II, or III) or Bonderite M-CR 600 Aero (Type I, II, or III). (4) Apply fastener seal (cap seal) with BMS5-45. (5) Apply BMS10-20 Type II fuel tank coating to any exposed alodine/bonderite surfaces not covered by the fastener seal; it is acceptable to extend BMS10-20 Type II coating over fastener seal. (i) Alternative Methods of Compliance (AMOCs) (1) The Manager, Seattle ACO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the certification office, send it to the attention of the person identified in paragraph (j)(1) of this AD. Information may be emailed to:
[email protected]. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (3) An AMOC that provides an acceptable level of safety may be used for any repair, modification, or alteration required by this AD if it is approved by The Boeing Company Organization Designation Authorization (ODA) that has been authorized by the Manager, Seattle ACO Branch, FAA, to make those findings. To be approved, the repair method, modification deviation, or alteration deviation must meet the certification basis of the airplane, and the approval must specifically refer to this AD. (j) Related Information (1) For more information about this AD, contact Chris Baker, Aerospace Engineer, Propulsion Section, FAA, Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206-231-3552; email:
[email protected]. (2) Service information identified in this AD that is not incorporated by reference is available at the addresses specified in paragraphs (k)(3) and (4) of this AD. (k) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) Boeing Special Attention Requirements Bulletin 737-57-1352 RB, dated February 1, 2021. (ii) [Reserved] (3) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; telephone 562-797-1717; internet www.myboeingfleet.com. (4) You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA,
[email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html. Issued on July 29, 2022. Christina Underwood, Acting Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2022-19902 Filed 9-14-22; 8:45 am]BILLING CODE 4910-13-P