2022-14-10: Wings

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by: a. Removing Airworthiness Directive (AD) 2018-13-08, Amendment 39-19320; (83 FR 33809, July 18, 2018); and b. Adding the following new AD: 2022-14-10 Airbus SAS: Amendment 39-22115; Docket No. FAA-2022-0468; Project Identifier MCAI-2021-01243-T. (a) Effective Date This airworthiness directive (AD) is effective August 19, 2022. (b) Affected ADs This AD replaces AD 2018-13-08, Amendment 39-19320 (83 FR 33809, July 18, 2018) (AD 2018-13-08). (c) Applicability This AD applies to the Airbus SAS airplanes identified in paragraphs (c)(1) through (4) of this AD, certificated in any category, as identified in European Union Aviation Safety Agency (EASA) AD 2021-0241, dated November 8, 2021 (EASA AD 2021-0241). (1) Model A318-111, -112, -121, and -122 airplanes. (2) Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes. (3) Model A320-211, -212, -214, -216, -231, -232, and -233 airplanes. (4) Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes. (d) Subject Air Transport Association (ATA) of America Code 57, Wings. (e) Reason This AD was prompted by a report that, during a center fuselage certification full-scale fatigue test, cracks were found on the front spar vertical stringer at a certain frame. This AD was also prompted by a determination that Model A321 airplanes that have incorporated modification 160021 are also subject to the unsafe condition. The FAA is issuing this AD to address fatigue cracking of the front spar vertical stringers on the wings, which, if not corrected, could result in the reduced structural integrity of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2021-0241. (h) Exceptions to EASA AD 2021-0241 (1) Where EASA AD 2021-0241 refers to its effective date, this AD requires using the effective date of this AD. (2) The "Remarks" section of EASA AD 2021-0241 does not apply to this AD. (3) Where paragraph (3) of EASA AD 2021-0241 specifies actions for airplanes repaired "in accordance with instructions approved by EASA or approved under Airbus DOA," for this AD use "using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature." (4) Where paragraph (4) of EASA AD 2021-0241 specifies to "contact Airbus for approved corrective action instructions and accomplish those instructions accordingly" if cracks are detected, for this AD if any cracking is detected, the cracking must be repaired before further flight using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature. (5) Where paragraph (8) of EASA AD 2021-0241 specifies actions for airplanes inspected by additional instructions "approved before the effective date of this AD by Airbus DOA," for this AD use "approved before the effective date of this AD by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature." (i) No Reporting Requirement Although the service information referenced in EASA AD 2021-0241 specifies to submit certain information to the manufacturer, this AD does not include that requirement. (j) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch, send it to the attention of the person identified in paragraph (k) of this AD. Information may be emailed to: [email protected]. (i) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (ii) AMOCs approved previously for AD 2018-13-08 are approved as AMOCs for the corresponding provisions of EASA AD 2021-0241 that are required by paragraph (g) of this AD. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (3) Required for Compliance (RC): Except as required by paragraph (j)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (k) Related Information For more information about this AD, contact Vladimir Ulyanov, Aerospace Engineer, Large Aircraft Section, International Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; phone 206-231-3229; email [email protected]. (l) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2021-0241, dated November 8, 2021. (ii) [Reserved] (3) For EASA AD 2021-0241, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email [email protected]; internet www.easa.europa.eu. You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email [email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html. Issued on June 29, 2022. Christina Underwood, Acting Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2022-15189 Filed 7-14-22; 8:45 am]BILLING CODE 4910-13-P