2019-19-02: Fuselage

Adoption of the Amendment \n\n\n\tAccordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: \n\n((Page 56680)) \n\nPART 39--AIRWORTHINESS DIRECTIVES \n\n0 1. The authority citation for part 39 continues to read as follows: \n\n\n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\n\n\nSec. 39.13 (Amended) \n\n0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): \n\n2019-19-02 The Boeing Company: Amendment 39-19738; Docket No. FAA- 2019-0524; Product Identifier 2019-NM-081-AD. \n\n(a) Effective Date \n\n\n\tThis AD is effective November 27, 2019. \n\n(b) Affected ADs \n\n\n\tNone. \n\n(c) Applicability \n\n\n\tThis AD applies to The Boeing Company Model 747-400 and 747-400F series airplanes, certificated in any category, as identified in Boeing Alert Requirements Bulletin 747-53A2900 RB, dated April 11, 2019. \n\n(d) Subject \n\n\n\tAir Transport Association (ATA) of America Code 53, Fuselage. \n\n(e) Unsafe Condition \n\n\n\tThis AD was prompted by an evaluation that determined fatigue cracks could develop in the underwing longerons. The FAA is issuing this AD to address cracks in the underwing longerons, which could result in fuel leakage into the pressurized fuselage and increase the risk of a fire, and to address cracks in the adjacent fuselage skin, which could result in rapid decompression. Either condition could adversely affect the structural integrity of the airplane. \n\n(f) Compliance \n\n\n\tComply with this AD within the compliance times specified, unless already done. \n\n(g) Required Actions \n\n\n\tExcept as specified by paragraph (h) of this AD: At the applicable times specified in the ''Compliance'' paragraph of Boeing Alert Requirements Bulletin 747-53A2900 RB, dated April 11, 2019, do all applicable actions identified in, and in accordance with, the Accomplishment Instructions of Boeing Alert Requirements Bulletin 747-53A2900 RB, dated April 11, 2019. \n\n\n\tNote 1 to paragraph (g): Guidance for accomplishing the actions required by this AD can be found in Boeing Alert Service Bulletin 747-53A2900, dated April 11, 2019, which is referred to in Boeing Alert Requirements Bulletin 747-53A2900 RB, dated April 11, 2019. \n\n(h) Exceptions to Service Information Specifications \n\n\n\t(1) For purposes of determining compliance with the requirements of this AD: Where Boeing Alert Requirements Bulletin 747-53A2900 RB, dated April 11, 2019, uses the phrase ''the original issue date of Requirements Bulletin 747-53A2900 RB,'' this AD requires using ''the effective date of this AD.'' \n\t(2) Where Boeing Alert Requirements Bulletin 747-53A2900 RB, dated April 11, 2019, specifies contacting Boeing for repair instructions: This AD requires doing the repair using a method approved in accordance with the procedures specified in paragraph (i) of this AD. \n\n(i) Alternative Methods of Compliance (AMOCs) \n\n\n\t(1) The Manager, Seattle ACO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the certification office, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: [email protected]. \n\t(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. \n\t(3) An AMOC that provides an acceptable level of safety may be used for any repair, modification, or alteration required by this AD if it is approved by The Boeing Company Organization Designation Authorization (ODA) that has been authorized by the Manager, Seattle ACO Branch, FAA, to make those findings. To be approved, therepair method, modification deviation, or alteration deviation must meet the certification basis of the airplane, and the approval must specifically refer to this AD. \n\n(j) Related Information \n\n\n\tFor more information about this AD, contact Eric Lin, Aerospace Engineer, Airframe Section, FAA, Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206-231-3523; email: [email protected]. \n\n(k) Material Incorporated by Reference \n\n\n\t(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. \n\t(2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. \n\t(i) Boeing Alert Requirements Bulletin 747-53A2900 RB, dated April 11, 2019. \n\t(ii) (Reserved) \n\t(3) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Contractual & DataServices (C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740- 5600; phone: 562-797-1717; internet: https://www.myboeingfleet.com. \n\t(4) You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. \n\t(5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email [email protected], or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.