2019-14-07: Fire protection

Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39--AIRWORTHINESS DIRECTIVES 0 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. [[Page 38855]] Sec. 39.13 [Amended] 0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): 2019-14-07 Airbus SAS: Amendment 39-19685; Docket No. FAA-2019-0251; Product Identifier 2019-NM-057-AD. (a) Effective Date This AD is effective September 12, 2019. (b) Affected ADs None. (c) Applicability This AD applies to Airbus SAS Model A320-251N and -271N airplanes; and Model A321-251N, -253N, -271N, and -272N airplanes; certificated in any category, as identified in European Union Aviation Safety Agency (EASA) AD 2019-0081, dated April 3, 2019 (``EASA AD 2019-0081''). (d) Subject Air TransportAssociation (ATA) of America Code 26, Fire protection. (e) Reason This AD was prompted by a report that during a calibration check, some torqueing tools used on the final assembly line have been found out of tolerance. The FAA is issuing this AD to address connections of sense and fire extinguishing lines within the pylon area that have been under-torqued, which could lead to leaks or disconnections of those lines and possibly result in reduced engine control and reduced safety margin in case of engine fire. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2019-0081. (h) Exceptions to EASA AD 2019-0081 (1) For purposes of determining compliance with the requirements of this AD: Where EASA AD 2019-0081 refers to its effective date, this AD requires using the effective date of this AD. (2) The ``Remarks'' section of EASA AD 2019-0081 does not apply to this AD. (i) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (3) Required for Compliance (RC): For any service information referenced in EASA AD 2019-0081 that contains RC procedures and tests: Except as required by paragraph (i)(2) of this AD, RC procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be putback in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (j) Related Information For more information about this AD, contact Sanjay Ralhan, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3223. (k) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2019-0081, dated April 3, 2019. (ii) [Reserved] (3) For EASA AD 2019-0081, contact the EASA, Konrad-Adenauer- Ufer 3, 50668 Cologne, Germany; telephone +49 221 89990 6017; email [email protected]; Internet www.easa.europa.eu. You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. (4) You may view this EASA AD at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. EASA AD 2019-0081 may be found in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA- 2019-0251. (5) You may view this material that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202- 741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.