2019-07-04: Editorial Note: Rule document 2019-07587 was originally published on pages 15949 through 15952 in the issue of Wednesday, April 17, 2019. In that publication, on page 15951, in the title of \n the Airworthiness Directive, ''-04'' was inadvertently left out. The corrected document is republished in its entirety.

Adoption of the Amendment \n\n\n\tAccordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: \n\nPART 39--AIRWORTHINESS DIRECTIVES \n\n0 1. The authority citation for part 39 continues to read as follows: \n\n\n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\n\n\nSec. 39.13 (Amended) \n\n0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): \n\n2019-07 The Boeing Company: Amendment 39-19615; Docket No. FAA-2018- 0899; Product Identifier 2018-NM-099-AD. \n\n(a) Effective Date \n\n\n\tThis AD is effective May 22, 2019. \n\n(b) Affected ADs \n\n\n\tNone. \n\n(c) Applicability \n\n\n\t(1) This AD applies to all The Boeing Company Model 757-200, - 200PF, -200CB, and -300 series airplanes, certificated in any category. \n\t(2) Installation of Supplemental Type Certificate (STC) ST01518SE does not affect the ability to accomplish the actions required by this AD. Therefore, for airplanes on which STC ST01518SE is installed, a ''change in product'' alternative method of compliance (AMOC) approval request is not necessary to comply with the requirements of 14 CFR 39.17. \n\n(d) Subject \n\n\n\tAir Transport Association (ATA) of America Code 53, Fuselage. \n\n(e) Unsafe Condition \n\n\n\tThis AD was prompted by an evaluation by the design approval holder (DAH) indicating that the inner skin of the lap splices, at the lower fastener row, is subject to scratch cracks that may interact with widespread fatigue damage (WFD). We are issuing this AD to address scratches that can grow into scratch cracks, which could interact with multi-site damage (MSD) fastener hole fatigue cracking. This condition, if not addressed, could result in accelerated crack growth rate, which could result in reduced structural integrity of the airplane. \n\n((Page 15952)) \n\n(f) Compliance \n\n\n\tComply with this AD within the compliance times specified, unless already done. \n\n(g) Required Actions \n\n\n\tExcept as specified by paragraph (h) of this AD: At the applicable times specified in the ''Compliance'' paragraph of Boeing Alert Requirements Bulletin 757-53A0111 RB, dated May 21, 2018, do all applicable actions identified in, and in accordance with, the Accomplishment Instructions of Boeing Alert Requirements Bulletin 757-53A0111 RB, dated May 21, 2018. \n\tNote 1 to paragraph (g) of this AD: Guidance for accomplishing the actions required by this AD can be found in Boeing Alert Service Bulletin 757-53A0111, dated May 21, 2018, which is referred to in Boeing Alert Requirements Bulletin 757-53A0111 RB, dated May 21, 2018. \n\n(h) Exceptions to Service Information Specifications \n\n\n\t(1) For purposes of determining compliance with the requirements of this AD: Where Boeing Alert Requirements Bulletin 757-53A0111 RB, dated May 21, 2018, uses the phrase ''the original issue date of Requirements Bulletin 757-53A0111 RB,'' this AD requires using ''the effective date of this AD.'' \n\t(2) Where Boeing Alert Requirements Bulletin 757-53A0111 RB, dated May 21, 2018, specifies contacting Boeing for alternative inspections or repair instructions, this AD requires alternative inspection or repair before further flight using a method approved in accordance with the procedures specified in paragraph (i) of this AD. \n\t(3) Inspections performed in accordance with Boeing Alert Requirements Bulletin 757-53A0111 RB, dated May 21, 2018, are not necessary in areas where existing FAA approved repairs cover the affected inspection areas; provided the outermost repair doubler extends a minimum of three rows of fasteners above and below the original group of lap splice fasteners subject to the inspection. Damage tolerance inspections specified for existing repairs must continue. Inspections outside of the repaired boundaries are still required as specified in Boeing Alert Requirements Bulletin 757- 53A0111 RB, dated May 21, 2018. \n\n(i) Alternative Methods of Compliance (AMOCs) \n\n\n\t(1) The Manager, Los Angeles ACO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the certification office, send it to the attention of the person identified in paragraph (j)(1) of this AD. Information may be emailed to: [email protected]. \n\t(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. \n\t(3) An AMOC that provides an acceptable level of safety may be used for any repair, modification, or alteration required by this AD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) that has been authorized by the Manager, Los Angeles ACOBranch, FAA, to make those findings. To be approved, the repair method, modification deviation, or alteration deviation must meet the certification basis of the airplane, and the approval must specifically refer to this AD. \n\n(j) Related Information \n\n\n\t(1) For more information about this AD, contact David Truong, Aerospace Engineer, Airframe Section, FAA, Los Angeles ACO Branch, 3960 Paramount Boulevard, Lakewood, CA 90712-4137; phone: 562-627- 5224; fax: 562-627-5210; email: [email protected]. \n\t(2) Service information identified in this AD that is not incorporated by reference is available at the addresses specified in paragraphs (k)(3) and (k)(4) of this AD. \n\n(k) Material Incorporated by Reference \n\n\n\t(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. \n\t(2) You must use this service information as applicable to do the actions required bythis AD, unless the AD specifies otherwise. \n\t(i) Boeing Alert Requirements Bulletin 757-53A0111 RB, dated May 21, 2018. \n\t(ii) (Reserved) \n\t(3) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740- 5600; phone: 562-797-1717; internet https://www.myboeingfleet.com. \n\t(4) You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. \n\t(5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.