2016-20-14: Fuselage

Adoption of the Amendment \n\n\n\tAccordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: \n\nPART 39--AIRWORTHINESS DIRECTIVES \n\n0 1. The authority citation for part 39 continues to read as follows: \n\n\n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\n\n\nSec. 39.13 (Amended) \n\n0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): \n\n2016-20-14 The Boeing Company: Amendment 39-18680; FAA-2016-5042; Directorate Identifier 2015-NM-140-AD. \n\n(a) Effective Date \n\n\n\tThis AD is effective November 15, 2016. \n\n(b) Affected ADs \n\n\n\tNone. \n\n(c) Applicability \n\n\n\t(1) This AD applies to all The Boeing Company Model 737-600, - 700, -700C, -800, -900 and -900ER series airplanes, certificated in any category. \n\t(2) Installation of Supplemental Type Certificate (STC) ST00830SE (http:// \n\n((Page 70013)) \n\nrgl.faa.gov/Regulatory_and_Guidance_Library/rgSTC.nsf/0/ 38B606833BBD98B386257FAA00602538?OpenDocument&Highlight=st00830se) does not affect the ability to accomplish the actions required by this AD. Therefore, for airplanes on which STC ST00830SE is installed, a ''change in product'' alternative method of compliance (AMOC) approval request is not necessary to comply with the requirements of 14 CFR 39.17. \n\n(d) Subject \n\n\n\tAir Transport Association (ATA) of America Code 53, Fuselage. \n\n(e) Unsafe Condition \n\n\n\tThis AD was prompted by an evaluation by the design approval holder indicating that certain fastener locations in the window corner surround structure are subject to widespread fatigue damage. We are issuing this AD to detect and correct fatigue cracking around certain fastener locations that could cause multiple window corner skin cracks, which could result in rapid decompression and consequent loss of structural integrity of the airplane. \n\n(f) Compliance \n\n\n\tComply with this AD within the compliance times specified, unless already done.(g) Repetitive Inspections and Repair \n\n\n\tAt the applicable time specified in paragraph 1.E., ''Compliance,'' of Boeing Alert Service Bulletin 737-53A1351, dated July 8, 2015: Do an external high frequency eddy current (HFEC) inspection for cracking of the skin around the fastener locations at the upper forward and lower aft corners of each window between station (STA) 360 and STA 540, as applicable, and at the lower forward and upper aft corners of each window between STA 727 and STA 887, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 737-53A1351, dated July 8, 2015. Repeat the inspection thereafter at the applicable times specified in paragraph 1.E., ''Compliance,'' of Boeing Alert Service Bulletin 737-53A1351, dated July 8, 2015. If any crack is found during any inspection, repair before further flight using a method approved in accordance with the procedures specified in paragraph (i) of this AD. \n\n(h) Exception to the Service Bulletin Specifications \n\n\n\tAlthough Boeing Alert Service Bulletin 737-53A1351, dated July 8, 2015, specifies to contact Boeing for repair instructions, and specifies that action as ''RC'' (Required for Compliance), this AD requires repair before further flight using a method approved in accordance with the procedures specified in paragraph (i) of this AD. \n\n(i) Alternative Methods of Compliance (AMOCs) \n\n\n\t(1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: [email protected]. \n\t(2) Before using any approved AMOC, notify your appropriate principalinspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. \n\t(3) An AMOC that provides an acceptable level of safety may be used for any repair, modification, or alteration required by this AD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) that has been authorized by the Manager, Seattle ACO, to make those findings. To be approved, the repair method, modification deviation, or alteration deviation must meet the certification basis of the airplane and the approval must specifically refer to this AD. \n\t(4) Except as required by paragraph (h) of this AD: For service information that contains steps that are labeled as RC, the provisions of paragraphs (i)(4)(i) and (i)(4)(ii) of this AD apply. \n\t(i) The steps labeled as RC, including substeps under an RC step and any figures identified in an RC step, must be done to comply with the AD. If a step or substep is labeled ''RC Exempt,'' then the RC requirement is removed from that step or substep. An AMOC is required for any deviations to RC steps, including substeps and identified figures. \n\t(ii) Steps not labeled as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the RC steps, including substeps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition. \n\n(j) Related Information \n\n\n\tFor more information about this AD, contact Gaetano Settineri, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle ACO, 1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-6577; fax: 425-917-6590; email: [email protected]. \n\n(k) Material Incorporated by Reference \n\n\n\t(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under5 U.S.C. 552(a) and 1 CFR part 51. \n\t(2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. \n\t(i) Boeing Alert Service Bulletin 737-53A1351, dated July 8, 2015. \n\t(ii) Reserved. \n\t(3) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone: 206-544- 5000, extension 1; fax: 206-766-5680; Internet: https://www.myboeingfleet.com. \n\t(4) You may view this service information at FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221. \n\t(5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.