2016-19-14: Equipment/Furnishings

Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39--AIRWORTHINESS DIRECTIVES 0 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. Sec. 39.13 [Amended] 0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): 2016-19-14 Airbus: Amendment 39-18663; Docket No. FAA-2015-8132; Directorate Identifier 2015-NM-127-AD. (a) Effective Date This AD is effective November 22, 2016. (b) Affected ADs None. (c) Applicability This AD applies to the Airbus airplanes identified in paragraphs (c)(1) through (c)(4) of this AD, certificated in any category; [[Page 71605]] except airplanes on which Airbus Modification 35869 has been embodied in production. (1) Airbus Model A318-111, -112, -121, and -122 airplanes. (2) Airbus Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes. (3) Airbus Model A320-211, -212, -214, -231, -232, and -233 airplanes. (4) Airbus Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes. (d) Subject Air Transport Association (ATA) of America Code 25, Equipment/ Furnishings. (e) Reason This AD was prompted by a report of cracks found during maintenance inspections on certain lugs of the 10VU rack side fittings in the cockpit. We are issuing this AD to prevent reading difficulties of flight-critical information displayed to the flightcrew during a critical phase of flight, such as an approach or takeoff, which could result in loss of airplane control at an altitude insufficient for recovery. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Repetitive Inspections and Repair At the later of the times specified in paragraphs (g)(1) and (g)(2) of this AD: Do a detailed inspection for cracking of the lugs on the 10VU rack side fittings in the cockpit, in accordance with the Accomplishment Instructions of Airbus Service Bulletin A320-92- 1087, Revision 02, dated November 25, 2014. If any crack is found, before further flight, repair in accordance with the Accomplishment Instructions of Airbus Service Bulletin A320-92-1087, Revision 02, dated November 25, 2014. Repeat the inspection thereafter at intervals not to exceed 20,000 flight cycles or 40,000 flight hours, whichever occurs first. Repair of the 10VU rack lugs does not terminate the repetitive inspections required by this paragraph. (1) Before the accumulation of 30,000 total flight cycles or 60,000 total flight hours, whichever occurs first since the airplane's first flight. (2) Within 24 months after the effective date of this AD. (h) Reporting Requirement Submit a report of any findings (positive and negative) of any inspection required by paragraph (g) of this AD to Airbus Service Bulletin Reporting Online Application on Airbus World (https://w3.airbus.com/), at the applicable time specified in paragraph (h)(1) or (h)(2) of this AD. Where Figure A-FRAAA--Sheet 02, titled ``Inspection Report,'' of Airbus Service Bulletin A320-92-1087, Revision 02, dated November 25, 2014, specifies sending removed lugs to Airbus for investigation, this AD does not include that requirement. The form contained in Figure A-FRAAA--Sheet 02, titled ``Inspection Report,'' of Airbus Service Bulletin A320-92-1087, Revision 02, dated November 25, 2014, may be used to meet this reporting requirement. (1) If the inspection was done on or after the effective date of this AD: Submit the report within 90 days after the inspection. (2) If the inspection was done before the effective date of this AD: Submit the report within 90 days after the effective date of this AD. (i) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Branch, send it to ATTN: Sanjay Ralhan, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057- 3356; telephone 425-227-1405; fax 425-227-1149. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA; or the European Aviation Safety Agency (EASA); or Airbus's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (3) Reporting Requirements: A federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to a penalty for failure to comply with a collection of information subject to the requirements of the Paperwork Reduction Act unless that collection of information displays a current valid OMB Control Number. The OMB Control Number for this information collection is 2120-0056. Public reporting for this collection of information is estimated to be approximately 5 minutes per response, including the time for reviewing instructions, completing and reviewing the collection of information. All responses to this collection of information are mandatory. Comments concerning the accuracy of this burden and suggestions for reducing the burden should be directed to the FAA at: 800 Independence Ave. SW., Washington, DC 20591, Attn: Information Collection Clearance Officer, AES-200. (4) Required for Compliance (RC): If any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (j) Related Information Refer to Mandatory Continuing Airworthiness Information (MCAI) European Aviation Safety Agency (EASA) Airworthiness Directive 2015- 0170, dated August 18, 2015, for related information. This MCAI may be found in the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA- 2015-8132. (k) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) Airbus Service Bulletin A320-92-1087, Revision 02, dated November 25, 2014. (ii) Reserved. (3) For service information identified in this AD, contact Airbus, Airworthiness Office--EIAS, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 44 51; email [email protected]; Internet http://www.airbus.com. (4) You may view this service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.