eFlight
FAA orders · airworthiness directive · historical

2010-24-12: Wings

FAA order 2010-24-12 is an airworthiness directive in force since January 20, 2011. The FAA's subject line: Wings. It names Boeing 777: about 359 aircraft on the U.S. register today, though an order usually covers particular versions or serial numbers rather than every one. System: fuel system.

What it applies to as the FAA lists it

Kind of product
Aircraft
Makes
The Boeing Company
Models
777-200 Series, 777-300 Series, 777-300ER Series
On this site
Boeing 777 359 registered

Dates and paperwork

In force since
January 20, 2011
Published
December 16, 2010 (signed November 18, 2010)
Docket
FAA-2007-27042
Replaced by
2011-26-03
Status
Historical
The FAA's document
Read the order on the FAA's site

The FAA's summary their words, unchanged

We are adopting a new airworthiness directive (AD) for certain Model 777-200, -300, and -300ER series airplanes. This AD requires installing Teflon sleeving under the clamps of certain wire bundles routed along the fuel tank boundary structure, and cap sealing certain penetrating fasteners of the main and center fuel tanks. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent electrical arcing on the fuel tank boundary structure or inside the fuel tanks, which could result in a fire or explosion.

The order itself the regulatory text, as published

Show the full text (7,416 characters)
2010-24-12 The Boeing Company: Amendment 39-16531. Docket No. FAA- 2007-27042; Directorate Identifier 2006-NM-225-AD. \n\nEffective Date \n\n\t(a) This airworthiness directive (AD) is effective January 20, 2011. \n\nAffected ADs \n\n\t(b) None. \n\nApplicability \n\n\t(c) This AD applies to The Boeing Company airplanes, certificated in any category, as identified in the applicable service information specified in Table 1 of this AD. \n\n\tTable 1--Service Information\n\n\nFor Model- \nBoeing- \n777-200, -300, and -300ER airplanes.\nService Bulletin 777- 57A0050, Revision 2, dated May 14, 2009. \n777-200 and -300 airplanes. \nAlert Service Bulletin 777-57A0051, dated May 15, 2006. \n777-200, -300, and -300ER airplanes. \nAlert Service Bulletin 777-57A0057, Revision 1, dated Au-gust 2, 2007. \n777-200, -300, and -300ER airplanes.\nAlert Service Bulletin 777-57A0059, dated October 30, 2008. \n\n\tNote 1: Although Boeing Service Bulletin 777-57A0050, Revision 2, dated May 14, 2009, refers to "Model 777-200ER'' airplanes, this is a European designation that does not apply to airplanes of U.S. registry. Therefore, the applicability of this AD will not specify Model 777-200ER airplanes. However, U.S. operators should consider any reference to Model 777-200ER airplanes in Boeing Service Bulletin 777-57A0050, Revision 2, as applicable to Model 777-200 airplanes as designated by the type certificate data sheet. \n\nSubject \n\n\t(d) Air Transport Association (ATA) of America Code 57: Wings. \n\nUnsafe Condition \n\n\t(e) This AD results from fuel system reviews conducted by the manufacturer. The Federal Aviation Administration is issuing this AD to prevent electrical arcing on the fuel tank boundary structure or inside the main and center fuel tanks, which could result in a fire or explosion. \n\nCompliance \n\n\t(f) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. \n\nCorrectiveActions (Installing Teflon Sleeving, Cap Sealing, One-Time Inspection) \n\n\t(g) Within 60 months after the effective date of this AD, do the applicable actions specified in paragraph (g)(1), (g)(2), (g)(3), or (g)(4) of this AD. \n\n\t(1) For airplanes identified in Boeing Service Bulletin 777- 57A0050, Revision 2, dated May 14, 2009: Install Teflon sleeving under the clamps of certain wire bundles routed along the fuel tank boundary structure and cap seal certain penetrating fasteners of the fuel tanks, in accordance with the Accomplishment Instructions of Boeing Service Bulletin 777-57A0050, Revision 2, dated May 14, 2009. \n\n\t(2) For airplanes identified in Boeing Alert Service Bulletin 777-57A0051, dated May 15, 2006: Cap seal certain penetrating fasteners of the fuel tanks, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 777-57A0051, dated May 15, 2006. \n\n\t(3) For airplanes identified in Boeing Alert Service Bulletin 777-57A0057, Revision 1,dated August 2, 2007: Do a general visual inspection to determine if certain fasteners are cap sealed and do all applicable corrective actions, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 777- 57A0057, Revision 1, dated August 2, 2007. Do all applicable corrective actions before further flight. \n\n\t(4) For airplanes identified in Boeing Alert Service Bulletin 777-57A0059, dated October 30, 2008: Cap seal the fasteners in the center fuel tanks that were not sealed during production, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 777-57A0059, dated October 30, 2008. \n\nCredit for Actions Done Using Previous Issues of the Service Bulletins \n\n\t(h) Actions done before the effective date of this AD in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 777-57A0050, dated January 26, 2006; or Revision 1, dated August 2, 2007; are acceptable for compliance with the corresponding actions required by paragraph (g)(1) of this AD, provided that the applicable additional work specified in Boeing Service Bulletin 777-57A0050, Revision 2, dated May 14, 2009, is done within the compliance time specified in paragraph (g) of this AD. The additional work must be done in accordance with Boeing Service Bulletin 777-57A0050, Revision 2, dated May 14, 2009. \n\n\t(i) Actions done before the effective date of this AD in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 777-57A0057, dated August 7, 2006, are acceptable for compliance with the actions required by paragraph (g)(3) of this AD. \n\nAlternative Methods of Compliance (AMOCs) \n\n\t(j)(1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to Attn: Margaret Langsted, Aerospace Engineer, Propulsion Branch, ANM- 140S, FAA, Seattle ACO, 1601 Lind Avenue, SW., Renton,Washington 98057-3356; telephone (425) 917-6500; fax (425) 917-6590. Or, e-mail information to [email protected]. \n\n\t(2) To request a different method of compliance or a different compliance time for this AD, follow the procedures in 14 CFR 39.19. Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office. The AMOC approval letter must specifically reference this AD. \n\n\t(3) An AMOC that provides an acceptable level of safety may be used for any repair required by this AD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) that has been authorized by the Manager, Seattle ACO, to make those findings. For a repair method to be approved, the repair must meet the certification basis of the airplane and the approval must specifically refer to this AD. \n\nMaterial Incorporated by Reference \n\n\nDocument\nRevision\nDate\nBoeing Alert Service Bulletin 777-57A0051 \nOriginal \nMay 15, 2006 \nBoeing Alert Service Bulletin 777-57A0057 \n1 \nAugust 2, 2007 \nBoeing Alert Service Bulletin 777-57A0059 \nOriginal \nOctober 30, 2008 \nBoeing Service Bulletin 777-57A0050 \n2 \nMay 14, 2009 \n\n\t(1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. \n\n\t(2) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65, Seattle, Washington 98124-2207; telephone 206-544-5000, extension 1, fax 206-766-5680; e-mail [email protected]; Internet https://www.myboeingfleet.com. \n\n\t(3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221. \n\n\t(4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http:// www.archives.gov/federal_register/code_of_federal_regulations/ ibr_locations.html.

Related safety bulletins advice on the same designs, not orders

2022-05-17AIR-22-09R1 · AUTOPILOT FLIGHT DIRECTOR SYSTEM: ALT HOLD Engaged on Takeoff on Boeing Model 777/787 common fleets.
2022-04-12AIR-22-09 · AUTOPILOT FLIGHT DIRECTOR SYSTEM: ALT HOLD Engaged on Takeoff on Boeing Model 777/787 common fleets.
2020-11-16AIR-20-19 · Flight Management Computing Software System
2020-06-11NM-20-11 · Autopilot System
2020-04-16NM-20-07 · Navigation - Glideslope System

Source: FAA Dynamic Regulatory System, airworthiness directives. The FAA's document is the authority; the register counts are this site's, from the FAA register of November 20, 2026. Connections as data: /graph/directive/2010-24-12.json · aircraft systems.

Aircraft

By kindModelsMakersEnginesFleetsWhat changed

Fly

Plan a flightAirportsLive mapRoutes and flightsFuels

Training and work

TrainingFlight schoolsGround schoolsPilot examinersMedical examinersJobs

Companies

DirectoryCharter operatorsFBOsRepair stationsClaim your listing

Safety and data

AccidentsRecords checkAnalyticsSAFxCHANGEThe graphAbout

Colours follow your device's light or dark setting.