eFlight
FAA orders · airworthiness directive · current

2026-22-12: Rotorcraft tail boom

FAA order 2026-22-12 is an airworthiness directive in force since December 17, 2026. The FAA's subject line: Rotorcraft tail boom. It names Bell 429: about 179 aircraft on the U.S. register today, though an order usually covers particular versions or serial numbers rather than every one. System: rotorcraft systems.

What it applies to as the FAA lists it

Kind of product
Aircraft
Makes
Bell Textron Canada Limited
Models
429
On this site
Bell 429 179 registered

Dates and paperwork

In force since
December 17, 2026
Published
November 12, 2026 (signed November 6, 2026)
Docket
FAA-2026-7227
Replaces
2022-20-11
Status
Current
The FAA's document
Read the order on the FAA's site

The FAA's summary their words, unchanged

The FAA is superseding Airworthiness Directive (AD) 2022-20- 11, which applied to certain Bell Textron Canada Limited Model 429 helicopters. AD 2022-20-11 required visually inspecting the external surface of the tail rotor (TR) gearbox support assembly, borescope inspecting or visually inspecting the inside of the tail boom, and performing a tactile inspection. Depending on the results of the inspections, AD 2022-20-11 required removing certain rivets from service or repairing gaps in accordance with an approved method. Since the FAA issued AD 2022-20-11, the manufacturer determined the repetitive inspection interval needs to be reduced. This AD requires the same actions as AD 2022-20-11 and reduces the inspection interval. The FAA is issuing this AD to address the unsafe condition on these products.

The order itself the regulatory text, as published

Show the full text (5,501 characters)
1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by: a. Removing Airworthiness Directive 2022-20-11, Amendment 39-22195 (87 FR 64152, October 24, 2022); and b. Adding the following new airworthiness directive: 2026-22-12 Bell Textron Canada Limited: Amendment 39-23514; Docket No. FAA-2026-7227; Project Identifier MCAI-2025-01754-R. (a) Effective Date This airworthiness directive (AD) is effective December 17, 2026. (b) Affected ADs This AD replaces AD 2022-20-11, Amendment 39-22195 (87 FR 64152, October 24, 2022). (c) Applicability This AD applies to Bell Textron Canada Limited Model 429 helicopters, certificated in any category, as identified in Transport Canada AD CF-2025-60R1, dated January 28, 2026 (Transport Canada AD CF-2025-60R1). (d) Subject Joint Aircraft System Component (JASC) Code 5302, Rotorcraft tail boom. (e) Unsafe Condition This AD was prompted by reports of failed rivets between the tail boom skin and the tail rotor (TR) gearbox support assembly. The FAA is issuing this AD to detect and correct failed rivets and rivets with inadequate grip length. The unsafe condition, if not addressed, could result in deterioration of the joint structural integrity, detachment of the TR gearbox support assembly, and loss of control of the helicopter. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Required Actions Except as specified in paragraphs (h) and (i) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, Transport Canada AD CF-2025-60R1. (h) Exceptions to Transport Canada AD CF-2025-60R1 (1) Where Transport Canada AD CF-2025-60R1 refers to its effective date, this AD requires using the effective date of this AD. (2) Where Transport Canada AD CF-2025-60R1 requires compliance in terms of air time, this AD requires using hours time-in-service. (3) Where paragraphs (1), (2), and (3) of Part II of Transport Canada AD CF-2025-60R1 specify "since the last inspection in accordance with Part I or Part II of AD CF-2021-15 or Part I of this AD", for this AD replace that text with "since the last inspection in accordance with Part I of this AD". (4) Where the material referenced in Transport Canada AD CF-2025-60R1 specifies "tactile check", this AD requires replacing that text with "tactile inspection". (5) Where the material referenced in Transport Canada AD CF-2025-60R1 specifies to submit a structural repair request, this AD requires repairing any gaps and replacing rivets in accordance with a method approved by the Manager, International Validation Branch, FAA; or Transport Canada; or Bell Textron Canada Limited's Transport Canada Design Approval Organization (DAO). If approved by the DAO, the approval must include the DAO-authorized signature. (i) No Reporting Requirement Although the material referenced in Transport Canada AD CF-2025-60R1 specifies to submit certain information to the manufacturer, this AD does not include that requirement. (j) Alternative Methods of Compliance (AMOCs) (1) The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the International Validation Branch, send it to the attention of the person identified in paragraph (k) of this AD and email to: [email protected]. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (k) Additional Information For more information about this AD, contact Soban Saeed, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: (316) 946-4123; email: [email protected]. (l) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this material as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) Transport Canada AD CF-2025-60R1, dated January 28, 2026. (ii) [Reserved] (3) For Transport Canada material identified in this AD, contact Transport Canada, Transport Canada National Aircraft Certification, 159 Cleopatra Drive, Nepean, Ontario, K1A 0N5, Canada; phone: (888) 663-3639; email: [email protected]. You may view this material on the Transport Canada website at tc.canada.ca/en/aviation. (4) You may view this material at FAA, Airworthiness Products Section, Operational Safety Branch, 10101 Hillwood Parkway, Fort Worth, TX 76177. For information on the availability of this material at the FAA, call (817) 222-5110. (5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email [email protected]. Issued on November 6, 2026. Steven W. Thompson, Acting Deputy Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2026-23007 Filed 11-10-26; 8:45 am]BILLING CODE 4910-13-P

Related safety bulletins advice on the same designs, not orders

2010-08-05SW-10-15R1 · Bell Helicopter Textron, Inc. Model 429 Helicopters with Certain Clam Shell Doors
2010-02-05SW-10-15 · Bell Helicopter Textron, Inc. (Bell) Model 429 Helicopters with Clam Shell Doors

Source: FAA Dynamic Regulatory System, airworthiness directives. The FAA's document is the authority; the register counts are this site's, from the FAA register of November 18, 2026. Connections as data: /graph/directive/2026-22-12.json · aircraft systems.

Aircraft

By kindModelsMakersEnginesFleetsWhat changed

Fly

Plan a flightAirportsLive mapRoutes and flightsFuels

Training and work

TrainingFlight schoolsGround schoolsPilot examinersMedical examinersJobs

Companies

DirectoryCharter operatorsFBOsRepair stationsClaim your listing

Safety and data

AccidentsRecords checkAnalyticsSAFxCHANGEThe graphAbout

Colours follow your device's light or dark setting.