1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by: a. Removing Airworthiness Directive 2021-17-02, Amendment 39-21685 (86 FR 48490, August 31, 2021); and b. Adding the following new Airworthiness Directive: 2024-15-14 ATR-GIE Avions de Transport Régional: Amendment 39-22806; Docket No. FAA-2023-1987; Project Identifier MCAI-2023-00807-T. (a) Effective Date This airworthiness directive (AD) is effective October 23, 2024. (b) Affected ADs This AD replaces AD 2021-17-02, Amendment 39-21685 (86 FR 48490, August 31, 2021) (AD 2021-17-02). (c) Applicability This AD applies to all ATR-GIE Avions de Transport Régional Model ATR42-200, -300, and -320 airplanes, certificated in any category. (d) Subject Air Transport Association (ATA) of America Code 31, Instruments. (e) Unsafe Condition This AD was prompted by false activation of the stall warning system due to wiring damage on the wire bundle between an angle of attack (AOA) probe and the crew alerting computer, and the development of additional wiring modifications and an aircraft flight manual (AFM) update to address the unsafe condition. The FAA is issuing this AD to address this condition, which could result in loss of control of the airplane during take-off and landing phases. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2023-0191, dated November 2, 2023 (EASA AD 2023-0191). (h) Exceptions to EASA AD 2023-0191 (1) Where EASA AD 2023-0191 refers to October 27, 2020 (the effective date of EASA AD 2020-0221), this AD requires using December 3, 2020 (the effective date of AD 2020-23-13, Amendment 39-21330 (85 FR 73407, November 18, 2020)). (2) Where EASA AD 2023-0191 refers to February 2, 2021 (the effective date of EASA AD 2021-0024), this AD requires using October 5, 2021 (the effective date of AD 2021-17-02). (3) Where paragraph (2) of EASA AD 2023-0191 refers to "discrepancies," for this AD, discrepancies include, but are not limited to, wire damage, missing or damaged conduits, and incorrect routing of wiring and conduits. (4) Where paragraph (8) of EASA AD 2023-0191 specifies "accomplish the additional work as identified in" replace that text with "accomplish the additional work as identified in section '1-ADDITIONAL WORK.' " (5) Where paragraphs (4) and (5) of EASA AD 2023-0191 specify to "inform all flight crews, and, thereafter, operate the aeroplane accordingly," this AD does not require those actions, as those actions are already required by existing FAA operating regulations (see 14 CFR 91.9, 91.505, and 121.137). (6) Where EASA AD 2023-0191 refers to its effective date, this AD requires using the effective date of this AD. (7) Where EASA AD 2023-0191 refers to July 19, 2023 (the effective date of EASA AD 2023-0134), this AD requires using the effective date of this AD. (8) This AD does not adopt the "Remarks" section of EASA AD 2023-0191. (i) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the International Validation Branch, mail it to the address identified in paragraph (j) of this AD or email to:
[email protected]. If mailing information, also submit information by email. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or ATR-GIE Avions de Transport Régional's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (j) Additional Information For more information about this AD, contact Shahram Daneshmandi, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 206-231-3220; email
[email protected]. (k) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this material as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2023-0191, dated November 2, 2023. (ii) [Reserved] (3) For EASA AD 2023-0191, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email
[email protected]; website easa.europa.eu. You may find this EASA AD on the EASA website at ad.easa.europa.eu. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th Street, Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email
[email protected]. Issued on September 12, 2024. Victor Wicklund, Deputy Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2024-21178 Filed 9-17-24; 8:45 am]BILLING CODE 4910-13-P