The U.S. aircraft register, updated daily
FAA orders · airworthiness directive · current

2022-19-01: Turbine Section

FAA order 2022-19-01 is an airworthiness directive in force since October 25, 2022. The FAA's subject line: Turbine Section. It names the General Electric GENX-2B67/P engine: about 35 aircraft on the U.S. register today, though an order usually covers particular versions or serial numbers rather than every one. System: engine.

What it applies to as the FAA lists it

Kind of product
Engine
Makes
General Electric Company
Models
GEnx-2B67/P
Engine series
General Electric GENX-2B67/P 35 aircraft

Dates and paperwork

In force since
October 25, 2022
Published
September 20, 2022 (signed August 29, 2022)
Docket
FAA-2022-0587
Status
Current
The FAA's document
Read the order on the FAA's site

The FAA's summary their words, unchanged

The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) GEnx-2B67/P model turbofan engines. This AD was prompted by the detection of an iron inclusion in a forging, which may reduce the fatigue life of certain low-pressure turbine rotor (LPTR) stage 4 disks and LPTR stage 6 disks. This AD requires the removal of certain LPTR stage 4 disks and LPTR stage 6 disks from service and replacement with parts eligible for installation. The FAA is issuing this AD to address the unsafe condition on these products.

The order itself the regulatory text, as published

Show the full text (3,360 characters)
1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2022-19-01 General Electric Company: Amendment 39-22170; Docket No. FAA-2022-0587; Project Identifier AD-2022-00394-E. (a) Effective Date This airworthiness directive (AD) is effective October 25, 2022. (b) Affected ADs None. (c) Applicability This AD applies to General Electric Company (GE) GEnx-2B67/P model turbofan engines with an installed: (1) Low-pressure turbine rotor (LPTR) stage 4 disk, part number (P/N) 2440M64P01, with serial number (S/N) JHVPD762, JHVPD763, JHVPD764, or JHVPD765; or (2) LPTR stage 6 disk, P/N 2440M66P01, with S/N JHVVD753 or JHVVD754. (d) Subject Joint Aircraft System Component (JASC) Code 7250, Turbine Section. (e) Unsafe Condition This AD was prompted by the detection of an iron inclusion in a forging, which may reduce the fatigue life of certain LPTR stage 4 disks and LPTR stage 6 disks. The FAA is issuing this AD to prevent fracture and subsequent uncontainment of the LPTR stage 4 disk and LPTR stage 6 disk. The unsafe condition, if not addressed, could result in uncontained debris release, damage to the engine, and damage to the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Required Actions (1) Before the affected LPTR stage 4 disk exceeds 3,000 cycles since new (CSN), remove the affected LPTR stage 4 disk from service and replace with an LPTR stage 4 disk eligible for installation. (2) Before the affected LPTR stage 6 disk exceeds 5,000 CSN, remove the affected LPTR stage 6 disk from service and replace with an LPTR stage 6 disk eligible for installation. (h) Definitions (1) For the purpose of this AD, an "LPTR stage 4 disk eligible for installation" is an LPTR stage 4 disk that does not have P/N 2440M64P01, with S/N JHVPD762, JHVPD763, JHVPD764, or JHVPD765. (2) For the purpose of this AD, an "LPTR stage 6 disk eligible for installation" is an LPTR stage 6 disk that does not have P/N 2440M66P01, with S/N JHVVD753 or JHVVD754. (i) Alternative Methods of Compliance (AMOCs) (1) The Manager, ECO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the certification office, send it to the attention of the person identified in paragraph (j) of this AD and email to: ANE-AD-AMOC@faa.gov. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (j) Related Information For more information about this AD, contact Alexei Marqueen, Aviation Safety Engineer, ECO Branch, FAA, 1200 District Avenue, Burlington, MA 01803; phone: (781) 238-7178; email: Alexei.T.Marqueen@faa.gov. (k) Material Incorporated by Reference None. Issued on August 29, 2022. Ross Landes, Deputy Director for Regulatory Operations, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2022-20289 Filed 9-19-22; 8:45 am]BILLING CODE 4910-13-P

Source: FAA Dynamic Regulatory System, airworthiness directives. The FAA's document is the authority; the register counts are this site's, from the FAA register of October 5, 2026. Connections as data: /graph/directive/2022-19-01.json · aircraft systems.