2020-03-24: Time Limits/Maintenance Checks

Adoption of the Amendment \n\n\n\tAccordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: \n\nPART 39--AIRWORTHINESS DIRECTIVES \n\n0 1. The authority citation for part 39 continues to read as follows: \n\n\n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\nSec. 39.13 (Amended) \n\n0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): \n\n2020-03-24 Dassault Aviation: Amendment 39-19848; Docket No. FAA- 2019-0872; Product Identifier 2019-NM-156-AD. \n\n(a) Effective Date \n\n\n\tThis AD is effective April 2, 2020. \n\n(b) Affected ADs \n\n\n\tThis AD affects AD 2010-26-05, Amendment 39-16544 (75 FR 79952, December 21, 2010) (''AD 2010-26-05''). \n\n(c) Applicability \n\n\n\tThis AD applies to Dassault Aviation Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 20-F5 airplanes, certificated in any category, on which the Supplemental Structural Inspection Program (SSIP) (Dassault Service Bulletin 730) hasbeen embodied into the airplane's existing maintenance or inspection program. \n\n(d) Subject \n\n\n\tAir Transport Association (ATA) of America Code 05, Time Limits/ Maintenance Checks. \n\n(e) Reason \n\n\n\tThis AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. The FAA is issuing this AD to address fatigue cracking, damage, and corrosion in principal structural elements, which could result in reduced structural integrity of the airplane. \n\n(f) Compliance \n\n\n\tComply with this AD within the compliance times specified, unless already done. \n\n(g) Maintenance or Inspection Program Revision \n\n\n\tWithin 90 days after the effective date of this AD, revise the existing maintenance or inspection program, as applicable, to incorporate the information specified in Chapter 5-40-01, Airworthiness Limitations, of the Dassault Falcon 20 Retrofit 731 Maintenance Manual, Revision 10, dated January 1, 2019. The initial compliance time fordoing the tasks is at the time specified in Chapter 5-40-01, Airworthiness Limitations, of the Dassault Falcon 20 Retrofit 731 Maintenance Manual, Revision 10, dated January 1, 2019, or within 90 days after the effective date of this AD, whichever occurs later. \n\n(h) No Alternative Actions or Intervals \n\n\n\tAfter the existing maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions (e.g., inspections) or intervals may be used unless the actions or intervals are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (j)(1) of this AD. \n\n(i) Terminating Action for Certain Requirements of AD 2010-26-05 \n\n\n\tAccomplishing the actions required by this AD terminates the requirements of paragraph (g)(1) of AD 2010-26-05 only for Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 20-F5 airplanes on which the SSIP has been embodied into the airplane's existing maintenance or inspection program. \n\n(j) Other FAA AD Provisions \n\n\n\tThe following provisions also apply to this AD: \n\t(1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (k)(2) of this AD. Information may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. \n\t(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or the European Union Aviation Safety Agency (EASA); or Dassault Aviation's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. \n\n(k) Related Information \n\n\n\t(1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA AD 2019-0201, dated August 20, 2019, for related information. This MCAI may be found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2019-0872. \n\t(2) For more information about this AD, contact Tom Rodriguez, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3226; email Tom.Rodriguez@faa.gov. \n\n(l) Material Incorporated by Reference \n\n\n\t(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. \n\t(2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. \n\t(i) Chapter 5-40-01, Airworthiness Limitations, of the Dassault Falcon 20 Retrofit 731 Maintenance Manual, Revision 10, dated January 1, 2019. \n\t(ii) (Reserved) \n\t(3) For service information identified in this AD, contact Tom Rodriguez, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3226. \n\t(4) You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. \n\t(5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For informationon the availability of this material at NARA, email fedreg.legal@nara.gov, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html. \n\n\n\tIssued on February 14, 2020. Lance T. Gant, Director, Compliance & Airworthiness Division, Aircraft Certification Service. (FR Doc. 2020-03936 Filed 2-26-20; 8:45 am) BILLING CODE 4910-13-P