2018-19-26: Time Limits/Maintenance Checks

Adoption of the Amendment \n\n\n\tAccordingly, under the authority delegated to me by the Administrator, \n\n((Page 49277)) \n\nthe FAA amends 14 CFR part 39 as follows: \n\nPART 39--AIRWORTHINESS DIRECTIVES \n\n0 1. The authority citation for part 39 continues to read as follows: \n\n\n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\n\n\nSec. 39.13 (Amended) \n\n0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): \n\n2018-19-26 Dassault Aviation: Amendment 39-19427; Docket No. FAA- 2018-0549; Product Identifier 2018-NM-014-AD. \n\n(a) Effective Date \n\n\n\tThis AD is effective November 5, 2018. \n\n(b) Affected ADs \n\n\n\tNone. \n\n(c) Applicability \n\n\n\tThis AD applies to all Dassault Aviation Model MYSTERE-FALCON 200 airplanes, certificated in any category. \n\n(d) Subject \n\n\n\tAir Transport Association (ATA) of America Code 05, Time Limits/ Maintenance Checks. \n\n(e) Reason \n\n\n\tThis AD was prompted by a determination that more restrictive maintenance requirements and airworthiness limitations are necessary. We are issuing this AD to address fatigue cracking, damage, and corrosion in principal structural elements; such fatigue cracking, damage, and corrosion could result in reduced structural integrity of the airplane. \n\n(f) Compliance \n\n\n\tComply with this AD within the compliance times specified, unless already done. \n\n(g) Maintenance or Inspection Program Revision \n\n\n\tWithin 90 days after the effective date of this AD, revise the maintenance or inspection program, as applicable, to incorporate Chapter 5-40-00, Airworthiness Limitations, Revision 17, dated December 20, 2017, of the Dassault Falcon 200 Maintenance Manual. The initial compliance time for accomplishing the actions is at the applicable time specified in Chapter 5-40-00, Airworthiness Limitations, Revision 17, dated December 20, 2017, of the Dassault Falcon 200 Maintenance Manual; or within 90 days after the effective date of this AD; whichever occurs later. \n\n(h) No Alternative Actions or Intervals \n\n\n\tAfter the maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions (e.g., inspections) or intervals may be used unless the actions or intervals are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (i)(1) of this AD. \n\n(i) Other FAA AD Provisions \n\n\n\tThe following provisions also apply to this AD: \n\t(1) Alternative Methods of Compliance (AMOCs): The Manager, The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (j)(2) ofthis AD. Information may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. \n\t(2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or the European Aviation Safety Agency (EASA); or Dassault Aviation's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. \n\n(j) Related Information \n\n\n\t(1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA AD 2018-0009, dated January 15, 2018, for related information. This MCAI may be found in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2018-0549. \n\t(2) For more information about this AD, contact Tom Rodriguez, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3226. \n\n(k) Material Incorporated by Reference \n\n\n\t(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. \n\t(2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. \n\t(i) Chapter 5-40-00, Airworthiness Limitations, Revision 17, dated December 20, 2017, of the Dassault Falcon 200 Maintenance Manual. \n\t(ii) Reserved. \n\t(3) For service information identified in this AD, contact Dassault Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, South Hackensack, NJ 07606; telephone 201-440-6700; internet http://www.dassaultfalcon.com. \n\t(4) You mayview this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. \n\t(5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.