2017-19-14: Time Limits/ Maintenance Checks

Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39--AIRWORTHINESS DIRECTIVES 0 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. Sec. 39.13 [Amended] 0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): 2017-19-14 Dassault Aviation: Amendment 39-19044; Docket No. FAA- 2017-0529; Product Identifier 2016-NM-123-AD. (a) Effective Date This AD is effective October 24, 2017. (b) Affected ADs This AD affects AD 2014-16-27, Amendment 39-17951 (79 FR 51071, August 27, 2014) (``AD 2014-16-27''). (c) Applicability This AD applies to Dassault Aviation Model FALCON 900EX airplanes, serial number (S/N) 97 and S/N 120 and higher, certificated in any category, with an original certificate of airworthiness or original export certificate ofairworthiness issued on or before November 1, 2015. (d) Subject Air Transport Association (ATA) of America Code 05, Time Limits/ Maintenance Checks. (e) Reason This AD was prompted by a determination that new or more restrictive maintenance requirements and/or airworthiness limitations are necessary. We are issuing this AD to prevent reduced structural integrity of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Revision of Maintenance or Inspection Program Within 90 days after the effective date of this AD, revise the maintenance or inspection program, as applicable, to incorporate the information specified in Chapter 5-40, Airworthiness Limitations, Revision 9, dated November 2015, of the Dassault Falcon 900EX EASy, Falcon 900LX, and Falcon 900DX Maintenance Manual. The initial compliance time for accomplishing the actions specified in Chapter 5-40, Airworthiness Limitations,Revision 9, dated November 2015, of the Dassault Falcon 900EX EASy, Falcon 900LX, and Falcon 900DX Maintenance Manual, is within the applicable times specified in the maintenance manual or 90 days after the effective date of this AD, whichever occurs later, except as provided by paragraphs (g)(1) through (g)(4) of this AD. (1) The term ``LDG'' in the ``First Inspection'' column of any table in the service information means total airplane landings. (2) The term ``FH'' in the ``First Inspection'' column of any table in the service information means total flight hours. (3) The term ``FC'' in the ``First Inspection'' column of any table in the service information means total flight cycles. (4) The term ``M'' in the ``First Inspection'' column of any table in the service information means months. (h) No Alternative Actions and Intervals After accomplishing the revision required by paragraph (g) of this AD, no alternative actions (e.g., inspections) or intervals may be used unless the actions or intervals are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (j)(1) of this AD. (i) Terminating Action Accomplishing the actions required by paragraph (g) of this AD terminates all requirements of AD 2014-16-27. (j) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (k)(2) of this AD. Information may be emailed to: [email protected]. Before using any approvedAMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or the European Aviation Safety Agency (EASA); or Dassault Aviation's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (k) Related Information (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA Airworthiness Directive 2016-0129, dated June 23, 2016, for related information. This MCAI may be found in the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2017-0529. (2) For more information about this AD, contact TomRodriguez, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-1137; fax 425-227-1149. (l) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) Chapter 5-40, Airworthiness Limitations, Revision 9, dated November 2015, of the Dassault Falcon 900EX EASy, Falcon 900LX, and Falcon 900DX Maintenance Manual. (ii) Reserved. (3) For service information identified in this AD, contact Dassault Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, South Hackensack, NJ 07606; telephone 201-440-6700; Internet http://www.dassaultfalcon.com. (4) You may view this service information at the FAA, Transport Standards Branch, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.