2014-20-16: Main Rotor Blade

Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39--AIRWORTHINESS DIRECTIVES 0 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. Sec. 39.13 [Amended] 0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): 2014-20-16 Brantly International, Inc.: Amendment 39-17989; Docket No. FAA-2012-1093; Directorate Identifier 2011-SW-020-AD. (a) Applicability This AD applies to the Brantly International, Inc., (Brantly) Model B-2, Model B-2A, and Model B-2B helicopters, with a main rotor (M/R) blade, part number (P/N) 248-101, 248-202, or 248-404, installed, certificated in any category. (b) Unsafe Condition This AD defines the unsafe condition as a crack or delamination in an M/R blade. This condition could result in loss of an M/R blade and subsequent loss of control of the helicopter. (c) Effective Date This AD becomes effective November 12, 2014. (d) Compliance You are responsible for performing each action required by this AD within the specified compliance time unless it has already been accomplished prior to that time. (e) Required Actions (1) Before the first flight of each day, visually check the top and bottom of each M/R blade for a crack. Pay particular attention to the M/R blade root area, the area around the lead/lag damper mounting fork, and the trailing edge. These actions may be performed by the owner/operator (pilot) holding at least a private pilot certificate, and must be entered into the aircraft records showing compliance with this AD in accordance with 14 CFR 43.9 (a)(1) through (4) and 14 CFR 91.417(a)(2)(v). The record must be maintained as required by 14 CFR 91.417, 121.380, or 135.439. (2) Within 8 hours time-in-service (TIS), for a helicopter with an M/R blade, P/N 248-101 or P/N 248-202, and for a helicopter with an M/R blade P/N 248-404 with 10 or more years or 1,000 or more hours TIS, whichever occurs first, remove each M/R blade and: (i) Using an inspector qualified to the American Society for Nondestructive Testing (ASNT) Level II or equivalent, eddy current inspect each M/R blade for a crack in accordance with paragraph 4 and paragraphs 7 through 17 of Brantly International B-2 Main Rotor Blade Root Skin Inspection Technique Number ET002, dated November 2007 (technique), except this AD only requires you to inspect the inboard first 12 inches of the top and bottom of each blade. Note 1 to paragraph (e)(2)(i) of this AD: A copy of the Technique is attached to Brantly International, Inc., Service Bulletin No. 111, dated February 10, 2011 (SB 111). (ii) Thereafter, at intervals not to exceed 300 hours TIS or five calendar years, whichever occurs first, repeat the eddy current inspection in accordance with the requirements of paragraph (e)(2)(i) of this AD. (iii) Using a metallic coin or tap hammer, tap inspect each M/R blade for delamination in the bonded areas as shown on SB-111, Section 4. Pay particular attention to the root area in the first 12 inches of the top and bottom of each M/R blade. (iv) Using a 10X or higher power magnifying glass, visually inspect the top and bottom of each M/R blade for a crack. (v) Thereafter, at intervals not to exceed 25 hours TIS, repeat the tap inspection in accordance with the requirements of paragraph (e)(2)(iii) of this AD and the visual inspection using a 10X or higher power magnifying glass in accordance with the requirements of paragraph (e)(2)(iv) of this AD. (3) Before further flight, remove from service any M/R blade with a crack, delamination within the inboard 12 inches, or total delamination greater than 2 square inches outside the inboard 12 inches. (f) Alternative Methods of Compliance (AMOCs) (1) The Manager, Rotorcraft CertificationOffice, FAA, may approve AMOCs for this AD. Send your proposal to: Marc Belhumeur, Senior Project Engineer, Rotorcraft Certification Office, Rotorcraft Directorate, FAA, 2601 Meacham Blvd., Fort Worth, Texas 76137; telephone (817) 222-5170; email 7-AVS-ASW-170@faa.gov. (2) For operations conducted under a 14 CFR part 119 operating certificate or under 14 CFR part 91, subpart K, we suggest that you notify your principal inspector, or lacking a principal inspector, the manager of the local flight standards district office or certificate holding district office before operating any aircraft complying with this AD through an AMOC. (g) Subject Joint Aircraft Service Component (JASC) Code: 6210, Main Rotor Blade. (h) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) Brantly International B-2 Main Rotor Blade Root Skin Inspection, Technique Number ET002, dated November 1, 2007. (ii) Brantly International Inc., Service Bulletin No. 111, dated February 10, 2011. (3) For Brantly service information identified in this AD, contact Brantly International, Inc., 621 South Royal Lane, Suite 100, Coppell Texas, 75019, telephone (972) 829-4638, email tarcher@superiorairparts.com. (4) You may view this service information at FAA, Office of the Regional Counsel, [[Page 60343]] Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas 76137. For information on the availability of this material at the FAA, call (817) 222-5110. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.