2002-15-04: Compressor impellers

2002-15-04 Honeywell International, Inc., (formerly AlliedSignal, Inc. and Textron Lycoming) T5313B, T5317 Series, and T53 Series Turboshaft Engines: Amendment 39-12832. Docket No. 2000-NE-32-AD. Applicability: This airworthiness directive (AD) is applicable to Honeywell International, Inc., (formerly AlliedSignal, Inc., and Textron Lycoming) T5313B series, T5317 series, and former military T53 series, turboshaft engines with centrifugal compressor impellers having serial numbers (SN's) 83317, 83327, 83328, or 83330 installed. These engines are installed on, but not limited to Bell Helicopter Textron 204, 205, and 209 series, and Kaman K-1200 series helicopters, and the following surplus military helicopters that have been certified in accordance with 21.25 or 21.27 of the Federal Aviation Regulations (14 CFR 21.25 or 21.27): Bell Helicopter Textron manufactured AH-1, UH-1, and SW-204/205 (UH-1) series. Note 1: This AD applies to each engine identified in the precedingapplicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For engines that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (i) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it. Compliance: Compliance with this AD is required as indicated, unless already done. To prevent premature failure of the impellers from being operated beyond their design service life, which could result in an uncontained engine failure, in-flight shutdown, or damage to the helicopter, do the following: Life Limits (a) When conducting a revised centrifugal compressor impeller operating cycle count on impellers having SN's 83317, 83327, 83328, or 83330, consider these impellers to be centrifugal compressor impeller P/N 1-100-078-07. The life limit must use the value as if these centrifugal compressor impellers are P/N 1-100-078-07. Revised Operating Cycle Count (Prorate) for T53 Engines (b) For T5313B series, T5317 series, and former military T53 series engines, within 25 operating cycles or 7 calendar days, whichever occurs first, after the effective date of this AD, perform the following: (1) Conduct a revised centrifugal compressor impeller operating cycle count (prorate) in accordance with paragraph 2.E.of the Honeywell International, Inc. Service Bulletin (SB) that applies to the engine, from the following list: (i) For T53-L-13B series engines, use SB T53-L-13B-0020, Revision 3, dated October 25, 2001. (ii) For T53-L-13B/D engines, use SB T53-L-13B/D-0020, Revision 1,dated April 25, 2001. (iii) For T53-L-703 engines, use SB T53-L-703-0020, Revision 1, dated April 25, 2001. (iv) For T5313B series and T5317 series engines, use SB T531B/ 17-0020, Revision 6, dated May 2, 2001. (2) Remove from service centrifugal compressor impellers with SN's 83317, 83327, 83328, or 83330, that exceed their new life limit as calculated in accordance with paragraph (b)(1) of this AD. Impeller Marking (c) At the next access to the centrifugal compressor impeller, mark the impeller by vibropeening a line over the -14 suffix, and vibropeen a -07 suffix immediately following the -14. Use the following vibropeening parameters: (1) Vibropeen to a depth of 0.001-0.006 inch. (2) Do not vibropeen within 0.30 inch of corners, fillets, or sharp edges. Definition (d) For the purpose of this AD, access to the centrifugal compressor impeller is defined as whenever the turboshaft engine is disassembled sufficiently as specified by the applicable maintenance manual, to expose the compressor impeller for marking in accordance with paragraph (c) of this AD. Inspection of Impellers on T5313B and T5317 Series Engines (e) For T5313B and T5317 series engines, inspect centrifugal compressor impellers having SN's 83317, 83327, 83328, or 83330, for cracks in accordance with the Accomplishment Instructions of Textron Lycoming SB No. T5313B/17-0052, Revision 2, dated December 16, 1993, as follows: (1) For those centrifugal compressor impellers installed on AlliedSignal, Inc. Model T5313B engines, accomplish the following: (i) For centrifugal compressor impellers with equal to or greater than 4,600 cycles in service (CIS) on the effective date of this AD, initially inspect within 200 CIS after the effective date of this AD. (ii) For those centrifugal compressor impellers with less than 4,600 CIS on the effective date of this AD, initially inspect no later than 4,800 CIS. (2) For those centrifugal compressor impellers installed on AlliedSignal, Inc. T5317 series engines, accomplish the following: (i) For those centrifugal compressor impellers with equal to or greater than 3,500 CIS on the effective date of this AD, initially inspect within 200 CIS after the effective date of this AD. (ii) For those centrifugal compressor impellers with less than 3,500 CIS on the effective date of this AD, initially inspect no later than 3,700 CIS. (3) Centrifugal compressor impellers found cracked in accordance with the Accomplishment Instructions of Textron Lycoming SB No. T5313B/17-0052, Revision 2, dated December 16, 1993, must be removed from service and replaced with a serviceable part that does not exceed the life limit. (4) If no cracks are detected, perform repetitive inspections of the centrifugal compressor impellers at intervals not to exceed 500 CIS since last inspection in accordance with the Accomplishment Instructions of Textron Lycoming SB No. T5313B/17-0052, Revision 2, dated December 16, 1993. Inspection of Impellers on T53-L-13B Series Engines (f) For T53-L-13B series engines with centrifugal compressor impellers having SN's 83317, 83327, 83328, or 83330, perform the following: (1) Within 25 operating hours from the effective date of this AD, inspect the centrifugal compressor impeller for cracks using the revised cycle count (prorate) required by paragraph (b)(1) of this AD, in accordance with Accomplishment Instructions of AlliedSignal, Inc. SB No. T53-L-13B-0108, Revision 1, dated November 22, 1999. (2) If cracks are detected, then prior to further flight, replace centrifugal compressor impellers found cracked in accordance with the Accomplishment Instructions of AlliedSignal, Inc. SB No. T53-L- 13B-0108, Revision 1, dated November 22, 1999, and replace with a centrifugal compressor impeller P/N 1-100-078-13/-14. (3) If no cracks are detected, perform repetitive inspections of the centrifugal compressor impellers at intervals not to exceed 100 operating hours since last inspection in accordance with the Accomplishment Instructions of AlliedSignal, Inc. SB No. T53-L-13B- 0108, Revision 1, dated November 22, 1999. (4) Within 300 operating hours or 6 calendar months, whichever occurs first, after the effective date of this AD, replace centrifugal compressor impellers having SN's 83317, 83327, 83328, or 83330, with a centrifugal compressor impeller P/N 1-100-078-13/-14. Replacement of centrifugal compressor impellers having SN's 83317, 83327, 83328, or 83330, with a centrifugal compressor impeller P/N 1-100-078-13/-14 constitutes terminating action for the inspection requirements of paragraphs (f)(1) and (f)(3) of this AD. Inspection of Impellers on T53-L-13B/D Series Engines (g) For T53-L-13B/D series engines with centrifugal compressor impellers having SN's 83317, 83327, 83328, or 83330, perform the following: (1) Within 25 operating hours from the effectivedate of this AD, inspect the centrifugal compressor impeller for cracks using the revised cycle count (prorate) required by paragraph (b)(1) of this AD, in accordance with Accomplishment Instructions of AlliedSignal, Inc. SB No. T53-L-13B/D-0108, Revision 1, dated November 22, 1999. (2) If cracks are detected, then prior to further flight, replace centrifugal compressor impellers found cracked in accordance with the Accomplishment Instructions of AlliedSignal, Inc. SB No. T53-L-13B/D-0108, Revision 1, dated November 22, 1999, and replace with a centrifugal compressor impeller P/N 1-100-078-13/-14. (3) If no cracks are detected, perform repetitive inspections of the centrifugal compressor impellers at intervals not to exceed 100 operating hours since last inspection in accordance with the Accomplishment Instructions of AlliedSignal, Inc. SB No. T53-L-13B/ D-0108, Revision 1, dated November 22, 1999. (4) Within 300 operating hours or 6 calendar months, whichever occurs first, after the effective date of this AD, replace centrifugal compressor impellers having SN's 83317, 83327, 83328, or 83330, with a centrifugal compressor impeller P/N 1-100-078-13/-14. Replacement of centrifugal compressor impellers having SN's 83317, 83327, 83328, or 83330, with a centrifugal compressor impeller P/N 1-100-078-13/-14 constitutes terminating action for the inspection requirements of paragraphs (g)(1) and (g)(3) of this AD. Inspection of Impellers on T53-L-703 Engines (h) For T53-L-703 series engines with centrifugal compressor impellers having SN's 83317, 83327, 83328, or 83330, perform the following: (1) Within 25 operating hours from the effective date of this AD, inspect the centrifugal compressor impeller for cracks using the revised cycle count (prorate) required by paragraph (b)(1) of this AD, in accordance with Accomplishment Instructions of AlliedSignal, Inc. SB No. T53-L-703-0108, Revision 1, dated November 22, 1999. (2) If cracks are detected, then prior to further flight, replace centrifugal compressor impellers found cracked in accordance with the Accomplishment Instructions of AlliedSignal, Inc. SB No. T53-L-703-0108, Revision 1, dated November 22, 1999, and replace with a centrifugal compressor impeller part number (P/N) 1-100-078- 13/-14. (3) If no cracks are detected, perform repetitive inspections of the centrifugal compressor impellers at intervals not to exceed 100 operating hours since last inspection in accordance with the Accomplishment Instructions of AlliedSignal, Inc. SB No. T53-L-703- 0108, Revision 1, dated November 22, 1999. (4) Within 300 operating hours or 6 calendar months, whichever occurs first, after the effective date of this AD, replace centrifugal compressor impellers having SN's 83317, 83327, 83328, or 83330, with a centrifugal compressor impeller P/N 1-100-078-13/-14. Replacement of centrifugal compressor impellers having SN's 83317, 83327, 83328, or 83330, with a centrifugal compressor impeller P/N 1-100-078-13/-14 constitutes terminating action for the inspection requirements of paragraphs (h)(1) and (h)(3) of this AD. Alternative Methods of Compliance (i) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, Los Angeles Aircraft Certification Office (ACO). Operators must submit their requests through an appropriate FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, Los Angeles ACO. Note 2: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the Los Angeles ACO. Special Flight Permits (j) Special flight permits may be issued in accordance with 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the helicopter to a location where the requirements of this AD can be done. DocumentsThat Have Been Incorporated by Reference (k) The inspections must be done in accordance with the following SB's: Document No. Pages Revision Date Honeywell International, Inc., SB T5313B/17-0020. Total pages 14 All. 6. May 2, 2001. Honeywell International, Inc., SB T53-L-13B-0020. Total pages 13 All 3 Oct. 25, 2001. Honeywell International, Inc., SB T53-L-13B/D-0020. Total pages 12 All 1 April 25, 2001. Honeywell International, Inc., SB T53-L-703-0020. Total pages 12 All 1 April 25, 2001. Textron Lycoming SB, SB T5313B/17- 0052. Total pages 8 All 2 Dec. 16, 1993 AlliedSignal, Inc., SB T53-L-13B-0108. Total pages 12 1 2 3-12 Original 1 Original July 22, 1999. Nov. 22, 1999. July 22, 1999. Allied Signal, Inc., SB T53-L-13B/D- 10108 Total pages 12 1 2 3-12 Original 1 Original July 22, 1999. Nov. 22, 1999. July 22, 1999. AlliedSignal, Inc., SB T53-L-703- 0108. Total pages 12 1 2 3-12 Original 1 Original July 22, 1999. Nov. 22, 1999. July 22, 1999. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from Honeywell International Inc. Aerospace Services Attn.: Data Distribution, M/S 64-3/2101-201, PO Box 29003, Phoenix, AZ 85038-9003; telephone (602) 365-2493, fax (602) 365-5577. Copies may be inspected, by appointment, at the FAA, New England Region, Office of the Regional Counsel, 12 New England Executive Park, Burlington, MA; or at the Office of the Federal Register, 800 North Capitol Street, NW, suite 700, Washington, DC. Effective Date (l) This amendment becomes effective on September 10, 2002.